Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I am using an nrf54l10 with the NRFconnect SDK. I would be interested in a solution to go into a low power state and wake up again after a specific time (multiple hours to...
Hello, I am trying to develop a 1000 Hz wireless gaming mouse. The mouse has a NRF52832 onboard and the dongle has a NRF52820 on it. (Cannot switch to 52840) I do know about...
Hi,
I am using zephyr v4.3.0, and have compiled the "https://github.com/zephyrproject-rtos/zephyr/tree/main/samples/boards/nordic/system_off" sample to
run it on a Adafruit...
Does Nordic provide an application like nrFConnect for Desktop that could be used with a nRF52840 USB Dongle for a ZigBee network survey? Use case: Scan environment for existing...
Hi,
I'm developing with nRF Connect SDK v2.9.0 in VS Code. I followed the exercise l1_e1 from the intermediate course. When I debug with breakpoints and the first breakpoint...
On the nRF52840 using ncs/zephyr v2.6.1, how can I explicitly configure the Coded PHY scheme (selecting either S=2 or S=8) for BLE Extended Advertising? Please provide the...
I tried to fully replicate the example from DevAcademy ( academy.nordicsemi.com/.../) for my project, and added a button and an LED in the overlay. However, once SB_CONFIG_BOOTLOADER_MCUBOOT...
Hello,
We need to interface the nRF54L15 with a 3-wires SPI slave (which uses one single bidirectional pin for MOSI and MISO).
I see two options here:
1. Connect the...
Issue
On the nrf54lm20 using DTLS with MbedTLS, MbedTLS's heap can be exhausted. This will result in a TLS handshake error. When this issue happens MbedTLS does not catch...
Hey,
I have a question regarding the watchdog in a low power application with dynamic sleep times of e.g. 1mim/10mim/1h. In the docs of nrf9160 and also nrf9151 it says...
Hey Nordic support, We want to perform EMC tests on the DECT NR+ for our product and need a continuous wave or tx tone sample for testing. I found the DECT NR+ shell sample...
I mean like when ever i click pristine build in the vs code i am getting this below error " Unable to build: SDK not found. Ensure that a valid SDK is used for the build configuration...
Hi,
We are using the NRF9151 with AT commands to replace our SIMCOM modems.
We would like to write the SIM profile data to the modem via AT commands just like SIMCOM...
Trying to config TDM SCK for: Master, 4 channels, 24 or 32 bits, 16 KHz...doing the math yields 1.536 or 2.048 MHz for SCK. I have 24 MHz or 32 MHz available as possible clock...
