Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hello,
I currently have a product using the nrf9160, that started development 4 or 5 years ago. The firmware uses SDK 1.6.1, and whilst I have had to correct some bugs...
It's now two years ago, and the ticket had a different scope. But one of the answers from Nordic there was:
"This is because the spec mandates that if the device gets rejected...
I have installed the NRF Connect app on my Windows 10 PC, using "Run as Administrator" and keep getting the following error message whenever I try to install any of the products...
This is also my Bluetooth Prj.conf
When I turn on 2.4G, there will be an error message. How can I solve it? BLE and 2.4G cannot coexist at the same time. Can I switch...
I'm using the NRF5340. When I open a standard example project located in the directory: nrf\samples\bluetooth\peripheral_uart (the well-known Bluetooth data transparent transmission...
I'm using the NRF5340. When I open a standard example project located in the directory: nrf\samples\bluetooth\peripheral_uart (the well-known Bluetooth data transparent transmission...
Hello Devzone,
How can the nRF5340 App core read the "version number" of the image flashed to the Network Core, e.g. the FW_INFO fields, or something similar?
I am using...
Hi,
Is there an API, data structure or else in nCS v2.9.0, monitoring of which i can understand if ble advertisement is active or not active or at fault.? Also, if at...
Hi, I am using sdk 2.3.0. I got the following warnings while building the project. The build finished without any error, but it didn't perform as expected. Should I concern...
I am building a project based on the aws_iot example. I am using sdk 2.3.0. I can connect with either lte-m or nb-iot, but I keep getting aws_iot_connect, error: -119. What...
Hello, I am working on a custom board with my own custom project. I want to perform DFU for all the images I mentioned. The mechanism for the OTA update will be as follows...
I am unable to read PDM microphone on my custom board or nrf54l15-dk.
My environment:
- nRF Connect SDK v3.0.2
- nrf54l15-dk
- custom board with Fanstel BM15C -...
Hello,
Revival of an old nrf52840dk board I would like to use for another project, I'm trying to flash a sample application to it but it always fails with the following...
The NDEF message is slightly different between Type 2 and Type 4. Type 4 has a 2 byte length field at the very beginning of the file, called NLEN. The NFC Type 4 example code...
Hi.
I made a board with nRF54L15. I would like to use P0.01 on nRF54L15 as GPIO output., but I failed to confirm P0.01 turn high.
Then, I asked nordic AI anything to solve...
