I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Can anyone clarify what information is stored in the nrf9160 chip barcode? For our manufacturing tests, we'd like to use a barcode-readable identifier on each board, and the...
Is there any documentation on what peak data rates are available on the nRF9151?
While the Cat-M, Cat-NB1 and Cat-NB2 standard max data rates are easily available, I have...
Hello, we are currently migrating from nRF Connect v2.9.1 to v3.0.2. When doing so, we found that the tinycrypt API was deprecated and decided to move things to mbedtls. We...
Hello,
I've an issue that I can't find clear instructions for the nRF5340 serial recovery for the network core.
Being able to update both cores from the bootloader level...
Hi
I am writng some peer information just after connection using pm_peer_data_store . I need to read the data stored to do the next task. As the FDS is asynchronous, i am...
When I run nrfutil toolchain-manager list I get output like the following:
The * indicates which toolchain version is currently active in my environment.
However, there...
We are just kicking off a new design with a nRF54L15. We would like to use the GRTC as a pseudo real-time-clock. We know that it retains its value through a reset and in system...
Hello,
I know this question is more related to Zephyr than Nordic, but I wanted to try asking here.
I’m using the SMP service to send files to my device on a LittleFS...
Hello Sir,
I am currently working with the chip :nRF54l15 and ncs:2.9.1
Now, I have designed an onboard PCB antenna using the nrf54l15 chip and flashed the peripheral_uart...
Hello, I'm trying to use BLE on nrf52833. I'm developping with segger embedded studio and I' m usign the BLE peripheral example "ble_app_blinky". Firstly I erased the flash...
Hello,
I downloaded the zip file "mfw_nrf9160_1.3.7.zip" from nordic and I am trying to upload it via the programmer tab in the nrf connect to desktop app, but I keep...
Hi
I have couple of questions,
GRTC work as RTC (Real Time Clock)?
If yes then why there are three dedicated pins? (P0.03,P0.04,P1.08) means we can use it at outside...
I've been trying to connect the LSM6DSO32 IMU to the nrf52840 via SPI, however the mcu is unable to detect the IMU no matter what I try. What are some ideas on how I can debug...
