I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am trying to make ble communication work with I2C but i cant make it work i dont understand what is the issue the code is being build but it does not advertise can someone...
I'm building a firmware for nRF52 which is using app timer v2 with RTC1. After a while, app_timer starts running many times faster than normal, and I'm not sure why. Nothing...
I use pc-ble-driver to control nRF52840 dongle. I want to speed up scanning of advertising time.
So I change SCAN_INTERVAL and SCAN_WINDOW.
How can I modify the parameters...
The enocean_switch example has MESH-config example, to store data in FLASH, within the mesh rules.
I use it in my app, IT WORKS, but the biggest data array what I can store...
hello folk,
I am working on nrf52840, I want it to assign Static UID of any kind that even won't change after the device gets reset.
I have already gone through "FICR...
Hi,
I am looking at using the nrf5340/nrf9160 in a device. In this device, I need to have high endurance storage of some data that must be kept secret, integrity checked...
Hi,
My project involves an nRF52840 DK connected to an accelerometer on a breadboard, connecting to my Mac via USB-micro.
I'm editing the twi_scanner SES project so...
nRF5_SDK_17.0.0_9d13099,
IDE Segger V4.52c
soft device s132
I took ble_app_uart example, and then modified it to run I2C, SPI. everything is working fine
problem I...
I have a question about how to perform DFU over Mesh.
I'm using nRF52840 device.
Following the steps at the URL below (Configuring and performing DFU over Mesh), I'm trying...
nRF5_SDK_17.0.0_9d13099,
IDE Segger V4.52c
soft device s132
Reading the spec of nrf52832 I saw I2S, I need to interface a MIC, so I selected I2S Mic SPH0645, but after...
Hello,
is there a way to record Advertising Packets on all three channels (37,38,39) simultaneously using 3 individual nRF52840-Dongles and piping the output to a stream...
Both Devzone and Mesh SDK 5.0 are mentioned that store user data in mesh should using flash manager.
But read the source code of the mesh SDK , the mesh SDK already called...
We have used nus profile for over a year, and it has worked as expected. Now we added security to the BLE connection, with ble sec connection enabled, it works as expected...
Hello everyone,
I am currently in the process of designing a prototype using the nRF9160 and I use the Nordic-Thingy91 as a reference for some parts. The Thingy91 uses the...
