Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Currently, I am having a problem with my BLE application. I am using nRF5_SDK_17.0.2_d674dde version. The BLE can advertise and can be seen by my phone. When my phone...
Hi,
For nRF9160, configured for GPS plus LTE: What version of nRF Connect SDK supports GPS+LTE in eDRX mode? Also, are there any plans to provide modem support for GPS+LTE...
Hi, I am trying to test the uart exemple on nrf52840 using external debugging as shown in figure but it doesn't function !!!!
are there any modifications that need to be...
nRf Gurus, I need your help! It is very hard for me to understand top level configuration of the soft devices and overall mentality. I am sure it will be very easy and convenient...
I want to create a 1MHz timer using TIMER2.
I try to start the timer with the following settings, but the device probably hangs.
I also use app_timer, is it a problem...
Hello, Not so long ago I asked this question and the solution I was given is still working for the devices I was using. Now I've received a new version of the device in which...
Hello,
I am using nRF52832 DK module(for master), and breakout board(for slaves, 4-slaves).
I have some problem while BLE communication.
First, I am wondering if I can...
Hi,
I'm getting error on connect to cloud server (socket.nouslogic.com:443) with error code is 45 ( EOPNOTSUPP).
Here are detail:
1. Using https_client example on nRF...
Hi,
I am going to use a timer in my code which includes ble_app_uart (using app_timer) and saadc examples. I need this timer to read time during the program.
I know...
what I use project is "ble_thread_dyn_template" , Is there any way to replace the app's UART console with 'BLE' - i.e. instead of receiving 'ot' commands from UART console...
I need to read (and clear) the general purpose retention register. I cant start the Soft Device just yet, so cant use the sd_power_gpregret_get and sd_power_gpregret_clr functions...
Hi there!
I'm back again, with another possibly stupid mistake. I'm using ARMGCC in combination with Make, nRF5 SDK, nRF SDK for Mesh, FreeRTOS and C++. I wrote my own mesh...
Hi Dev team,
I am currently using the NCS v1.5.0 and have a Thingy91 v1.4.0 with me. I want to test the FOTA v2 update from the nRF Cloud to the Thingy91.
I tried using...
I am trying to tune my NFC antenna . The antenna is printed on the pcb. The same Laird antenna is used in my pcb. Based on the antenna tuning white paper I am trying to tune...
