Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi, i have written code in android, where i am using threads to connect to 832 ble over insecure RFComm socket..
Am not pairing with 832 in my app and am directly trying...
Hi I am implementing a buttonless_DFU function right now. I decided to do Buttonless on my project's PCB Board because it is no longer an environment where I can add switches...
My setup is as follows:
nRF5 SDK 13.1 with s132 5.1.0
nRF52832_AA
Keil 5.25pre
I use RTC1 counter for timestamping along with app_timer timers. My get_timestamp() function...
I am trying to send lots of data through radio (basing on old micro esb project from github, but heavily modified).
I need to keep radio IDLE (not DISABLED) when not transmitting...
Hi,
I am developing smartphone controlled BLE door lock based on nRF52840.
The door lock is a peripheral (also GATT server) and the smartphone is central (GATT client...
Using the nRF52840 with SDK15.3.0 and S140, I am seeing strange interactions between PWM and BLE.
The PWM is configured to create a continuous 175kHz output just under...
I am currently developing with nrf52832 sdk14.2. When nrf52832 is bound to a different iphone connection, if the stored binding record of nrf52832 is already full, will the...
Hello,
We require a bluetooth low energy IC with MCU. Right now we are testing with nrf51422 development board. Could you please suggest any updated ICs with (BLE+MCU) ...
Hi
Below picture and attached file is my 52810 hardware.
All the component are accord with the 52810 data sheet.
But, when I download the BLE blinky project from the...
Hi I am currently testing Buttonless DFU using SDK 12.3, nRF52832 DK. Example test was conducted first using the DK board, but as you can see in the picture, it will fail...
Hi,
I have a MQTT-sample based application running and everything works fine. If I supply the DK through a USB cable connected with my computer, LED 5 blinks high frequently...
Hi,
I am using nRF5 SDK 15.2 and the twi_sensor example to read over I2C a slave device 'WhoAmI' memory location. I first tx the slave address (0x68) and then attempt to...
Hi,
I am using nRF52832 mcu, trying to run the flash data storage example but is having some trouble.
I followed the instructions to set up the terminal setting for UART...
Hello
Hello Using nRF5_SDK_12.3.0 examplesble_centralble_app_multilink_central as a host to send data to slaves and receive data from slaves is no problem. The problem is...
