Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi
I am using Ubuntu 16.04 and the latest version of nrf Connect for desktop and JLINK. Initially, there were some errors related to the serial port. Once I upgraded JLINK...
Hello!
On the Nordic website there stands that Keil is supported. So I am currently using it throw the Package but i got a problem with the correct partitioning in Keil...
HI ,
I have built a mesh based network based on the light switch sample.
Now I'd like to take it to the next step - I'd like the pass 70 Bytes of data between nodes (...
I am using the nrf51-dk on windows 10 and I tried to apply the latest mbed bootloader. After I do that and restart the chip, the device seems to mount and dismount repeatedly...
hi all
i want to make BLE peripheral app for send data to via UART but i don't know about which sample good for my purpose? so please tell me which sample good for my requested...
Hello
I have a very strange behaviour with debugging the mqtt_simple example for the nRF9160. The example is crashing in debugg configuration. (This happens with Segger...
I am using Nordic SDK 14.2.0 with the pca10040 and I want to integrate the Buttonless DFU functionality into my project (started with the Nordic BLE app template).
I tested...
Hi All
I want to add some custom source files (.c) & header files (.h) to an existing project.
I tried adding it by right clicking "Project app/libapp.a" branch of the...
I'm getting started developing an app for nRF52811. have worked with nRF52832 before. I was wanting to start my development on top of the basic ble app template project, from...
Hi,dear engineers,
I refer to the examples in nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_buttonless_dfu\pca10040\s132. I Port it into my own program. it seem...
I try to send the NRF_LOG_INFO() messages over a own backend interface. I tried to add a new backend with nrf_log_backend_add() and enable it with nrf_log_backend_enable(...
I am trying to do Secure DFU through WebUSB [1] . I need suggestions to move forward.
Some starting points I found :
DFU Protocol
I did saw that SDK 15.3.0 outlines...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96 ,PC is windows 10 .My testing master device is cell phone(Huawei HTC and so on,android system),and using...
Hi all,
Our custom board has 2 MCUs connected each other via UART to implement 2-chip configuration.
One is the main MCU which has Cortex R4 and the other is nRF52810...
