I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I have an nRF52840 chip ( Holyiot nRF52840 module ) and I want to program the chip using an nRF52840 DK. The Holyiot module is basically an nRF52840 mounted on a...
I am having trouble turning on bonds for DFU.
First of all, before I describe this pain, can I choose to avoid this battle by just allowing unbonded devices to DFU? e.g...
Hello!
I just bought the Beacon Kit and i was following the user guide v1.1 and I have some questions about how to use DFU. I have already downloaded nRF Toolbox app.
...
Hi,
I am using fatfs of nRF5_SDK_15.0.0_a53641a. I am writing a program with keil.
I want to know how to write the value obtained from the sensor to the SD card. ...
I am using proximity profile in sdk15 with softdevice 6.0.0 . I added flash write, writing continuously some data to flash. But it working sometimes only.
Hello,
at the moment my application is accepting more than one device if its not connected to anything. But I want that the application only connects to one device and...
Hello, i am using NRF52840 board with SDK 15.2. I am trying to read data from an advertising packet and i was just wondering if anybody on here had a good parser i could potentially...
Is it possible replace HRS to UART service (like ble_app_uart) on BLE LE Secure Connections multirole example project?
Any suggestion to easy to modify it?
Hello,
I am trying to get CLI working over UART and simultaneously use RTT for logging. I don't quite get my head around this. My platform is the nRF52840 DK. I am using...
Hi everyone,
I'm developping on nRF52840 with SDK 15.0.0 and Softdevice S140 v6.0.0
I'm using Peer Manager for pairing and bonding.
Everything work fine with io_caps...
The only examples I've found have been for ordinary single ended measurements at lower resolution, and even that is a crazy number of lines of code. Surely by now there is...
Dear nordic,
I want to change advertising data(manufacturer data including company identifier) before i start advertising
i choose central and peripheral example(because...
When I use the uart to transparently transmit, there is no problem at around 4k/s. When I increase the transparent transmission rate, there will be NRF_ERROR_SVC_HANDLER_MISSING...
Hi, I have the ble_app_uart with OTA functionality on SDK11 that works. Now I want to do the same with SDK12, but I see things have changed now. I've found this tutorial:...
