In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
I have just received my development kit and following the getting started instructions on website. But I am stuck at point 7 of this link https://www.nordicsemi.com/eng/Products...
hello Nordic team
I am using nrf52DK.how to use spi to read /write data .I have seen sdk14.2.0 in folder nRF5_SDK_14.2.0_17b948a\examples\peripheral\spi.
I am trying to interface an atmega32 with an nRF24L01. I am trying to communicate between two nRF's. But before proceeding to that, I set out to test the SPI connection between...
I put the nrf_ble_ancs_c_request_attrs in the BLE_ANCS_C_EVT_NOTIF event(added). But only return back 1 or 2 BLE_ANCS_C_EVT_NOTIF_ATTRIBUTE event. I am using 12.3.0 SDK example...
Hello,
This in reference to Case ID: 121570.
We are developing a wearable device with NRF52 as a Beacon with CR2032 coin cell battery from Panasonic. We have calculated...
i am using my custom board with nrf51822 and using sdk 12.3.0 .
the led blink example works fine on it but when i upload ble_app_uart then bluetooth is not advertising.
Hi i just get nRF52832 PCA10400 DK.
I am using SDK14.0.0. i tried to use /example/peripheral/spi.
i don't set the gpio set and high or low.in the SDK14.0.0, how to set...
Hi!
I'm using a barebones example project from SDK 12.3.0, under examples/peripheral/uart, with two versions of nRF52-DK boards (pca10056 and pca10040). The goal is to read...
Hi,
I am looking for the carrier tape spec for nRF52810-CAAA.
I am referring to the following document but nRF52810 is not listed.
nWP024 - Embossed Tape and Reel...
Hi,
I'm using a NRF52832 development kit and SDK v14.1. My application is simulating several bluetooth devices for testing purposes. The device I'm simulating doesn't support...
Dear All. I have question about compiler of nRF5_SDK_V12.3. I compile the example BLE_peripheral\experimental_ble_app_blinky by gnu arm(latest version). It can work on nRF51...
Hi,
I am having problems with a custom board using pin 0.10 as GPIO.
I have added -DCONFIG_NFCT_PINS_AS_GPIOS to my makefile. Without that, as expected, I am unable to...
Hi,
In the latest infocenter page, see:
http://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.0.0/lib_crypto_backend_micro_ecc.html?resultof=%22micro...
I am in the process of building software to drive a bare metal widget based on the nrf52840 - currently against the DK board. We have an in-house abstraction interface layer...