Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi,
I have nrf52 Thingy board and i want to read temperature sensor data using twi sensor example available in SDK 11. I am not able to get data.
Thanks
Hi Support team,
I am looking to replace my BLE chip by a nRF8001. I am currently using a DA14580 (Dialog Semiconductor), in Beacon mode or pairing mode. I saw that the...
Hi,
As given in the link: http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.tools%2Fdita%2Ftools%2Fpower_profiler_kit%2FPPK_user_guide_Troubleshooting...
Hi, would you support with the following:
In the high voltage mode (defined as when the supply voltage is only connected to the VDDH pin and the VDD pin is not connected...
(Overview) When accessing the I2C device connected to the Nordic controller nRF 52832, The CLK frequency changes during the process, resulting in operation at an unintended...
I have the nRF52 Dev Kit running now on Mac OS with SES.
(for reference to this topic: click here )
My end result is to use the nRF52 chip as part of a MIDI wind controller...
Dear All,
I am looking for EMI/EMC testing for my custom board based on nRF52832 board. Could you please provide any generic firmware for the same. Is there any UI to test...
Hi
I have my application running on nRF52 on SDK 11 (Softdevice S132 version 2.0). I am using 1 peripheral and 6 central links in my application. I am migrating the application...
HI, i have a small question. When I downloaded the hardware files of thingy52, and opened altium files, I can not move components in a pcb layout, i have to split windows...
Hi,
To decrease the load on the system I would like to periodically send some BT data (and do some SD card writing).
Since Timer 0 is used by the soft device, I am using...
I want an amplifier to receive audio from a FM/DAB receiver and from an NRF52832 that - in turn - has received audio over BLE. The amplifier should either receive the radio...
when I start to program nRF52832 under 1.8v some memory pages can't be accessed. this is short listing:
Erasing page at address 0x78000. Erasing page at address 0x79000...
Hello,
I'm trying to make some current measurement using the nRF6707 and a nRF5 SDK Board(10040) (Board out of the box, shunts untouched).
We're facing problems measuring...
Hello,
Does the newest SoftDevice release v5.1.0 support the advertising data length extension (255 bytes)? If not, will it be available this year?
We are at the evaluation...
Hi,
I am using nRF52832 DK (PCA10040) SDK 14.2.0 and S132 V5.1.0.
I am planning to test the TWI loopback (in order to familiarise the APIs used for TWI in nRF52).
I...
