Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I find "led_radio_example" and "button_radio_example" as 2.4G transceiver with nRF51822.
Is there any example source code about how nRF24L01 can talk with nRF51422?
Hello,
I'm modyfiyng a NUS template. I noticed, that when I move to far with my Android phone (with the nRF UART v2.0 app) from the NRF51 PCA10000 board, it disconnects...
The above mentioned example ( here ) is the one that is available in GitHub.
I want to implement bonding with static passkey based on SD110 v8 and nRF51822 with Device Manager...
I've tried to drop in all non-main code from the spi 5W example into my program and I keep getting the following errors:
.\_build\nrf51422_xxac_s110.axf: Error: L6218E...
Hi -
Looking for a layout review of the NRF51822 antenna and oscillator design attached. The two main questions are:
Is it recommended to remove the copper ground...
Hi,
any plans to release firmware package for nrf51822 smart beacon using Soft device 8 and SDK 8? Thinking I better ask before I start adapting it on my own.
thanks...
What is the pinout on the DEBUG OUT-pins?
How do I adapt the code to work both with dev board and an external chip?
There are BSP stuff I probably can't use that I use for...
I am using S110 7.1.0 which I know has the ability to unblock the CPU during Radio Event. However I would like to do the opposite and increase the time between a Radio event...
Any news on the new specification for S130?
I am trying to find out the concurrent power profile. It the power management section it said that it has not be characterized...
Well, I've ordered my preview nRF52-DK and might get it by the weekend. I have not been able to find the schematics and design files on the main Nordic site, or the new infocenter...
This project is a HRS example from latest SDK, without any modification. I use nrf51 DK board. WHen I debug, I get hardfault after some type. Try to run the code under debugger...
Hi,
we used NRF_UARTE_Type POWER for the "peripheral power control" of the UART interface on nrf51 - works fine.
After trying to port the nrf51 to nrf52 I found out...
The question is: how to completely turn off PWM in SoftDevice?
I am using the libraries nrf_pwm.h and nrf_pwm.c in this repo for PWM with SoftDevice. Everything seems to...
