Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi, I am now using nRF24lu1p, for using cklf_wdog_init() to enable watchdog, then I set cklf_wdog_init(10) in main function, but don't know how to set watchdog event handle...
So we have been developing on the nRF52811 and realized we need OTA (Over the air Frimware) aswell and we have 30kB Flash and 8kB Ram remaining. Can this be done?
Also a...
Dear Sir/Madam,
I am trying following,
1. Avoiding SPIM transfer interrupt handler.
I am performing following steps,
1. nrf_drv_spi_init() for Handler parmater 'NULL...
Hello,
I'm using nRF connect for power profiling of nRF52840 DK. First time it works.
If we close the nRF connect and open it again then I get error.(Also after power...
How can I do LESC on my central with an Android peripheral device, if with each new connection the MAC address on Andriod changed randomly?
The first time I am making a...
Hello,
I want to use 100 bytes of flash as non-volatile data memory. We should be able to read and write this memory during execution.
So for this purpose I need the implementation...
I already follow the link for terminal in this link https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v16.0.0%2Flib_cli.html&cp=6_1_3_10_3&anchor=lib_cli_terminal_settings...
nRF52DK
p20 debug out
external board is 51822 + sensors
I managed to connect the external board through p20 on the 52DK. I can successfully program the external board...
I am reading about nRF52811 SoC which is currently supported by nRF5 SDK v15.3.0 and SoftDevice S112.
I want to know more about its direction finding capabilities and play...
Hi,
I'm trying to add the NUS service to an existing application (freertos based, SDK15.2, already use a custom service)
I copied the relevant code snippets from...
Hi everyone,
I'm trying to use nRF52810 with SoftDevice S112 to sample five ADC channels. I'm finding this very weird issue, where first channel is showing correct value...
Just getting started with Nordic toolchain and I got this error below.
=== updating civetweb (modules\lib\civetweb): --- civetweb: cloning and initializing Initialized...
i need a code for when button press after one second delay led will glow continiously whenever again pressing the switch it will stop glowing using apptimer
Hi, Everyone
My development environment is sdk15.3, nRF52840, Keil complier
The link error file is attached below.
Also I am going to use AES-CBC method.
Which example...
