Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
Hi Everybody
When I run my code with the debugger, it always crashes when executing sd_softdevice_enable(). Even if there is no breakpoint activated. However, when I run...
SDK 15.3 API S132
How can i implement the HFCLK using softdevice or how can i enabled it
I need to be able to run an SK6812 which has the following timing requirements...
I'm attempting to make a custom program using a few different libraries based on the samples. In attempting to initialize nvs, it returns -22. I've been able to trace it deep...
Why does " app:" appear in my serial port when reading from ble_app_hrs_c from the SDK for nrf52dk. I was looking to remove this part sending to the com port but I cannot...
Hello to all,
We have developed our application & the following platform we are using:
SDK 15.0, Segger IDE on windows PC
Softdevice version is 6.0.0
Hardware version...
Hello,
I'm using SDK15.3.0, softdevice S132 v6.1.1 and we would like to know if it is possible to combine the application and the bootloader in the same ZIP file in order...
Are the MIPI and MAGPIO interfaces mutually exclusive, or is it possible to setup nRF9160 to use both? For instance, can I use MIPI to control RF switches, but at the same...
Hi,
I've created a project combining gps, nvs, and mqtt based off the nrf and zephyr project samples. I've been able to go into the sample projects and add .overlay files...
Hi.
I'm dfu test for sdk13.
NRF52832 EVM board
nrfutil version : nrfutil version 3.2.0
D:\nordic_nrf52832>**nrfutil.exe dfu ble -ic NRF52 -f -pkg dfu_test_app_hrm_s132...
Hi, i want to use dfu for application with mesh. But i want to update via ble in direct connection with phone, not via mesh protocol. Should i use example from mesh sdk or...
nrf52832 is connected to the main controller of the circuit on uart lines (RX and TX).
We have observed that even when we completely cut-off the power of nrf52832 then also...
Hi
I used the SDK 14.2, and download the android source code from guthub. Because I sent many packets(about 100 packets), so the delay should be set in the Android. I tried...
Hello, I am using nrf52832. I am adding pwm library in dfu secure boot loader project. I imported all required library but can't find PWM enable drivers/ library option in...
Good day!
I'm interesting in ability to support of some required Cybersecurity features by NRF52832 or/and NRF52840:
Is it possible to fully disable JTAG and/or SWD...
