Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi.
I have nRF51422 borad and want to flash to nRF51422 with JLink.
I supplied to 3.3V power to board and is connedted SWDIO to p23, SWDCLK to p24. JLink is connected...
Hi,
I am desperate with creating my own board. I followed the example of nrf54l15dk, but I absolutely do not understand why I cannot build - not even assembling Zephyr....
Hello,
I am working on custom hardware that is based on the nRF7002 DK. The following parts are presently listed as either EOL or NRND in distribution. L6, L8: Taiyo Yuden...
I am trying to connect some I2C sensors to the the nrf9151dk and I cannot figure it out. Where do I physically plug the sensor into the board and what configuration setting...
Hello,
Hopefully this will be a quick(ish) one since I think I found the answer, but just need confirmation.
To preface (My setup):
nRF9151DK
Modem firmware: mfw_nrf91x1_2...
I am currently attempting to send HTTP requests (GET and POST) with my nRF9160 DK over an LTE connection. I have tried running the HTTP client sample code under zephyr/samples...
Hello! One of our projects will have nRF52832 replaced in EMS with revision 3 silicone and we wonder if description in is valid. It states that:
In factory state, the [new...
Dear Nordic-Support,
I have registered handlers for the two voltage level thresholds with the nrf modem library using modem_battery_low_level_handler_set and modem_battery_pofwarn_handler_set...
Hi Nordic Team,
I am working on implementing synchronized sensor sampling on multiple Bluetooth devices that are externally triggered. To achieve this, I have combined the...
Hello,
Before I start to over-develop I need to ensure that there isn't a better solution based on the nPM1300 behavior or capabilities.
Context
I'm using an nPM1300...
Hello,
we are testing the channel sounding performances for distance measurement with the example:
https://docs.nordicsemi.com/bundle/ncs-2.9.1/page/nrf/samples/bluetooth...
Is there any way to sniff BLE 6.0 packets and see the new content such as channel sounding? I am familiar with the nRF52840 Dongle as a sniffer in Wireshark, is there similar...
Hello all, i made a board with this BLE chip:
nRF52832-CIAA-R
What happens is that when i enable power supply i can see the circuit is properly in advertise ( i can scan...
Hello,
I am currently working with the nRF5340DK and the W5500 shield. Both work perfectly when using the dhcpv4_client application. However, when I attempt to use the recv...
I'm running the peripheral_ancs_client using the 2.9.0 SDK on a nRF5340-DK. On an iPhone running iOS18, the device is not visible under Settings->Bluetooth when the nRF5340...
Hello, I am currently developing a testing software to verify whether all the pins of my module have been properly connected. I configured pin 1.03 as a high level in the...
