I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
We'd like to implement a feature that allows changing a BLE connection from [central device #1 -> peripheral] to [central device #2 -> same peripheral] (similar to Apple...
Dear friends,
The nRF Connect BLE app is connected with a local device acted as Master. The app supports the configuration of the local device's GATT attribute table, and...
Hello,
After i uploaded a program on my nRF52832 i couldn't enter debug or reprogram the chip. This is the error i get when trying to erase the chip using Segger J-Flash...
Hi,
I am using peer manager to use static passkey with nrf51822, sdk11 and s130 v2.
Is the "case PM_EVT_CONN_SEC_START:" the best place to put sd_ble_gap_tx_power_set...
I know this question has been asked before. As a beginner to Nordic, I tried to get the information here, but ended up even more confused.
I am trying to set up a Bluetooth...
Hi,
I developed a unit on NRF52 which is "CENTRAL". This unit connects to multiple "PHERIPHERAL" units and it's working great.
Now, i need to connect this "CENTRAL" unit...
app_timer.h is include two times in : examples\ble_peripheral\ble_app_ancs_c\main.c examples\peripheral\spi_master_using_nrf_spi_mngr\main.c examples\peripheral\twi_master_using_nrf_twi_mngr...
We are using the nRF52832 to scan for surrounding beacons on an interval (scan for 60 seconds, sleep for 30 minutes). During some of these scans, not all beacons are picked...
Hi,
I'm trying to run some examples using my nRF52840 . I noticed that the BLE header files used in the SDK 14.2.0 are different than what's in the standalone S140 (6.0...
I have connected the board to a PC and it prompted a JLINK folder when connected to a PC. However, when I tried an example project on the IAR workbench, I think I clicked...
I have custom board with nrf52832. I use latest nrf5 sdk 14. Problem is that when I am connected with SWD and RTT then everything works perfectly. But when I disconnect SWD...
hello , i'm trying to read my file fatfs in sdk , i have the instruction created with vivado HLS but i can't translate by my self in fatfs. some help please
this the instruction...
While Digikey is listed as a Canadian supplier, they do not have ANY of the dev kits. That is to say, they won't ship them to Canada. They have them. They are listed on nordic...
Hi,
I am using ble_app_uart sample code. In that I want to run a timer based on the commands received in BLE. i.e., if command received is 'one' , LED1 should ON for one...
Hello,
I asked about this on openthread-users ( https://groups.google.com/forum/#!topic/openthread-users/F8_NmMRDOFE ) and got redirected here. Generally, I observed a severe...
