Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I'm new to using the Nordic SDK and I'm trying to use the BLE template to start my own service. Is there a walk-through for doing this somewhere that may be able to help?...
Hello,
I'm developing a simple code that make use of timers using NRF-based boards and Arduino code.
The following code works fine on a Simblee nRF51822 board , but...
I was trying to install firmware into my nRF51 Dongle using jlink.exe on Windows, so I can use nRF Sniffer. I made the mistake of unplugging the dongle from USB after erasing...
I have an nRF52832, coding with SEGGER and the SDK 14.2.0. I'm trying the ble_peripheral/ble_app_uart example (although I get similar results with the other BLE examples)...
Using a pushbutton while advertising, the GPIOTE_IRQHandler handles the pushbutton click OK, but then the processor resets. The RESETREAS is code 4, aka. RESET from soft reset...
Hi,
I have couple of queries that need to be sorted,
http://www.nordicsemi.com/eng/Products/S112-SoftDevice, Says that S112 supports 2-peripheral connection and 1 broadcaster...
I want advertise the peripheral periodically only. i implement the logic it is working fine.but my doubt is once i connected to connected to central device advertise is no...
Noted the difference between the layouts concerning antenna matching among DK 0.9 and DK 0.11.
DK 0.9
DK 0.11
The screenshots are for L3. Differences between...
Hello,
I have a requirement to implement the following functionality. Can this be done?
Basically i need to store some customer info on the NFC NTAG. This has to customizable...
I am using nRF Connect for desktop v2.3.0. In my DIS service Firmware Revision String characteristic I am using a string of 30 characters. But when I connect to my device...
Hi,
We are looking into developing a device based on 52832 platform.
How many devices (phones) can be paired with our device?
In other words: How many pairing keys can...
See attachment - enlarge if it's too small. How can I get nRF Connect on my Windows 10 laptop to bring more than 20 characters, and also print in text (instead of hex values...
I would like to know the part number for the Side facing RGB LEDs used in the Nordic Thingy 52. I couldn't find the Bill of Material for the Thingy 52.
Hi. I got TCA6424A IC which communicates through i2c. I tried to use that with nordic but it doesnt respond. I used simple twi scanner application which should print address...
