Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
We are upgrading some products to SDK 14.2 and creating some new ones.
We need to start production programming of boards. I can't find the information on how to do this...
What is the maximum and minimum frequency of the PWM signal/square wave that can be measured on the NRF 52DK board I'm using NRF 52832.
Also, what is the max and min "pulse...
Hello,
I have found similar questions on transmitting multiple bytes over SPI, but I am still not sure how to do it. I want to communicate with a driver which needs to be...
Hi,
I found the 'Solar Sensor Beacon' example from
https://github.com/NordicPlayground/solar_sensor_beacon .
There, I found that no softdevice initialisation (nrf_sdh_ble_enable...
I am working through the nordic sdk 8.1 peripheral heart rate monitor example. I am wondering what RR is? I can't figure out what it stands for or what the purpose of it is...
Hi,
In my current project I have indicating LEDs connected via TWI bus. In this case, I can't use BSP_LED_0/BSP_LED_1 outputs to indicate states as it implemented in nrf_ble_dfu...
Hello, I recently use nrf52832 to make a wireless sensor network of BLE concurrently with NRF_ESB.
During development, I use only 2 sensor. Both sensors are connected to...
ANT S212, nRF52:
I've read all the links in the forum regarding serial port running in debug mode and not in run mode.
In my case, it works in RUN mode until softdevice_setup...
Hi
I have a sensor array which data have to be advanced burst to one or many devices.
The array size is anything from 24 bytes to 24k bytes, depending on the number of...
Hi guys,
I am using nrf51822 and SDK 11. I have some trouble about suddenly reset the nrf51822.
In my application, I used uart_fifo to received some information from other...
Hello beacon fellows,
with regards to maintenance, i am looking into the possibilities to avoid human presence when updating the message to be emitted by Beacon Kit. Any...
Hi,
I'm trying to do (customized / simplified) dual bank DFU on NRF52832 as simple as possible, without any complicated checks.
Assume I succeeded into storing the new...
i want to know about how nrf51822 beacon's states will change once it is turned ON.
with the state diagram i can define how the module is working after turning it ON.
...
Hi,
I am trying to configure the nRF52832 on my custom board to work on the 32.768KHz clock signal from the host controller. I have configured the LFCLKSRC register to use...
