Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi all
According to errata 146 of the nRF52832 Rev 1 errata sheet V1.5, the LFRC oscillator has a frequency tolerance of 500ppm instead of 250ppm.
What are the consequences...
I have a bootloader compiled from SDK 14.0, and when I try to upgrade to 14.1, the new linker script (secure_dfu_ble_gcc_nrf52.ld) does not contain the UICR_BOOTLOADER memory...
Hi,
I'm using the nrf51822 and I want to merge Server and Client roles in one Peripheral device. I am already able to send a history of temperature and humidity measurements...
Sometimes when the method RequestData is called after receiving a notify on the characteristic, the Master Emulator seems to hang for a set amount of time before throwing...
Hi guys,
I have troubles with MCP 3.10.0.14 but the device (PCA10031) cannot be detected in my laptop (Win 7 enterprise). I actually checked it on other PCs and everything...
Hi, I have just taken on responsibility for maintaining some firmware written for the nRF24LE1. One file, radio.c, contains the copyright header:
/* Copyright (c) 2008...
Can a proxy node also be a client and server node (a controller node)?
What are the key differences between a server and a client in BLE mesh?
Can a server relay a packet...
Hi,
When I try to download code to my nRF52832 from Keil with the example "BLE ATT_MTU Throughput Example", I get this error: Error: Flash Download failed - "Cortex-M4...
i want make delay funtion by timer?
in the other MCU like PIC, AVR, stm. i find register that hold value counter and i cant set this value
for example:
timer 8 bit will...
Hello
Just to confirm:
is it OK to use 2-layer PCB with nRF52840?
In case a 4-layer is needed, when do you advise the use of a 4-layer pcb?
Basically we...
I am trying to build the project which I downloaded from github for the "A beginner's tutorial: Advertising" but I get errors for missing files when I try to build it both...
How the ble peripheral knows that ble central was disconnected?
if i trying to send continuously some packets to ble peripheral some times peripheral is not responding?
...
Hello, everyone~
As the title, is there a complete tutorial for that? I even don't know if I can download the project directly without flashing SoftDevice additionally...
Dear Nordic Devzone,
Just recently I purchased 2 additional nRF52840. In total I have 6 of them now;
The first four all have the following numbers on the chip:
pca10056...
Hello,
I've found a lot of topics about this issue but none resolved my case.
I'm trying to program a custom N51822 board (QF ACA 1) but without success.
These are...
