Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi, I'm developing a BLE application.
I want to send multiple packets (from same characteristic) per connection interval.
I've read this question:
devzone.nordicsemi...
hello,
I am trying to develop an application using s130 softdevice on NRF51822 board.
i am able to do a undirected adverisement after a scanning. But when i am trying...
Hi
I use proprietary service to transmit data between iOS and nRF51822. The example I referred to is below.
C:\Keil\ARM\Device\Nordic\nrf51822_v6.0.0.43681_Backup\Board...
Hello,
I need to send packets on a specified advertising channel and receive them at the same advertising channel. Unfortunately, the SoftDevice API does not seem to support...
Hi,
I have several nRF51822 which are far away from each other and I want to communicate with all of them without need to go to deferent places to get the signal.
Does...
Hi
What is the scan interval ,while using the nrf51822 dongle as nrf sniffer.Is it possible to change this interval or is there any option provided in the sniffer api ...
Hi, we are using the nRF51422 and the s310 soft device using the 5.2 SDK.
In ble_error_log.c I noticed that you have a comment suggesting that write to flash was removed...
I have already installed nRF51_SDK_7.1.0_372d17a_packs. The examples in this SDK are only for nRF51422. Can I use these example in nRF51822 by just change device to nRF51822...
I was going through the figure 10 of page 35 of nRF24L01+ product specifications and found that when an ACK is received, it checks for only ACK payload. Does it mean that...
Hello,
I have implemented the ble UART service in the s120 example : ble_app_multilink_central. I can receive messages that are sent from a ble UART peripheral in the ...
I'm trying to use the bond manager to store links.
I used the ble_uart application posted in this site by a Nordic employee and tried to use the bond manager as it was done...
Hello,
i can't find the characteristic read timeout in BLE Core SPEC 4.0. If the central device read a characteristic from the peripheral device, in which time the peripheral...
Hello
I have uploaded a hex file which for some reason I cannot see the tag anymore, is there any way to re-program, erase or reflash the beacon kit using nrf51 programmer...
i was trying to implement bonding in ble_app_hrs example(SDK V6.1.0 and soft device v7.0.0)
i have given params
#define SEC_PARAM_TIMEOUT 30
#define SEC_PARAM_BOND 1...
