Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
For some sort of geofencing application, we want to include the BLE module nRF51822 into a Base Station (BS), and a small mobile device (MS).
The MS should detect the presence...
I have 2 moduls from ebay (rfinchina). I write little librarie for nRF24L01 and my msp430.
When i start my coard and init spi and try read few register - i have problem....
Hi,I use 51822 to make a fitness device. one of the function is advertising current value(Steps,Heart rate,Distance,Calorie) to the phone over BLE. What the default service...
I downloaded nRF51 SDK 5.2.0 and I am studying the examples for S120.
I notices that there's no gcc directory, thus only Keil compiler can be used. Is there a way to use...
Hello,
I have some questions regarding bluetooth low energy and the NRF51 series.
[list=1]1) I have to synchronise maximum 17 sensors, so i will maximum need 4 masters...
Hi.
I am looking for the internal resistance of the ADC pin of my nrf51822. I have looked at the Product Specifications (as well as the Reference Manual and other documents...
I find it unstable to send hid data, even if I set timer 1 every 8ms to send hid data.
I can catch data bag from wireshark it seems that interval of two data even close...
Hi All:
The hardware is working perfectly up until I changed some codes in the program and load it on the chip then I am unable to program again. The error message is:...
1.Size of EPROM. Is it big enough for our program as well as our data file for the whole day?
2.How can we secure the EPROM so that no one else can overwrite our code or...
We have an application that is an apple ibeacon, plus some extra properties that can be read (battery level for example)
The "ibeacon profile" eats up all the space in the...
Hi Guys,
i'm a newbie, trying to get the heart rate demo project working.
I've connected the nRF8001 to my own hardware, using a PIC processor.
i'm able to connect...
Hi,
I have a question about the service profile (ex:heart rate service, battery service,etc...), these services are based on protocol of IEEE11073-20601? Actually, I want...
See subject. The softdevice is currently installed on the chip (v6.0.0-1.alpha)
I searched online, and found some information that the security state of the chip has been...
Hi all,
When I receive data from the phone app, I do it via this service handler (and it works):
err_code = ble_services_init(&my_device_service, ble_receive_handler...
