I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello Nordic-Team,
i made a custom pcb that is based on the reference schematic of the nRF52810 QFAA with dcdc setup. However, i read that in general, the nRF52810 and nRF52832...
I would like to connect the Android Things NXP Pico board to the Nordic Thingy 52 using Bluetooth and get all sensor data from the thingy.
The Android Things board will...
Hello
Recentlly, our application with android device and nrf52, we need to do pairing process with android device in order to read characteristic from nrf52. The pairing...
I am using PCA10040 devkit and SdK11. Our application is to advertise at an interval of 100ms. Also, our application wants to spend most of the time in sleep mode. Currently...
hello , i am trying to imblement system off or system on in one of the ble central example 'ble_app_blinky_c' , i tried to refer to this example 'ble_app_template' but if...
Hi all ,
I am beginning with DFU . I complete bootloader_secure_ble and can update new firmware (application) to my NRF52832 kit via Android . And now, I have 2 kit NRF52...
hi team,
i am wondering that lot of questions regarding gps and wifi interface with nrf52 is there. why nordic is not supporting with libraries and examples for gps and...
Hi there,
I read that the nRF52840 has a maximum data throughput of around 1.3~1.4Mbps . I also read that when configured as a central it can support up to 20 concurrent...
Hello,
Can anyone point me to a good example for Polling mode using serial library?
I'm looking for an application in which I can poll the serial port for data. I went...
I'm investigating the flash usage by the peer manager to store bond related data. While I haven't had a chance to fully investigate how the FDS and fstorage modules work,...
Hi,
We have a need to have a Nordic app for nRF51822 which both serves as a beacon and also offers a connectable service.
It's my distinct impression at present we cannot...
Hi,
My setup :
nRF52832
Soft Device S132 v5
SDK14.2
My use case involve me to send data to to a central device at 50 meters. I need to send only a small data...
Hello everyone :) , I work on a project initialy configured for a PCA10040 board and I would like to use the debug with my PCA10056 board but unfortunatly the debug doesn...
Hi
For some reason I get stuck in softdevice at 1EA7A when a send some random data to my phone also I notes that function sd_ble_gatts_hvx return 3401
PC = 0001EA7A, CycleCnt...
