I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I am using "nrf5 sdk v11.0" ble_peripheral "ble_ancs_c" example for nrf52_DK(PCA10040) .
When i connect to the my ios device then accepted pairing request then i am...
is it possible configure the QDEC to single phase, i am using one omnipolar hall effect sensor i am wondering if i can configure only phase A ande use it, is it possible ...
Hi, I wonder why my pwm uses so much power in WFI mode. It uses around 470uA and when I do not use pwm that current is around 1.8uA. I tried to disable pwm but without success...
if i am not wrong the connections i found is as i shown in the image..
the module doesn't show up in my ide tool (keil ) although my kit works fine but i need it for standalone...
Dear Nordic Team,
I am work DFU with ble_app_uart example , as per the info center document : infocenter.nordicsemi.com/index.jsp and also followed by the example for ble_app_hrs...
when use the sd_ble_gatts_hvx() send data and printf() the value below
p_ble_evt->evt.gatts_evt.params.hvc.handle
p_ble_evt->evt.gatts_evt.params.sys_attr_missing.hint...
how to save a problem,if one Thread use sd_ble_gatts_hvx() send many package ,but i use vTaskDelay(50)( the freertos delay api ) when one package send ,then send another package...
ru.txt ra.txt Can someone help out in this. There is no option to capture the data in RTT. Somehow I am not able to take a screenshot directly from the Windows on my MAC.
i to all, I have just bought NRF51 DK from arrow.com I couldn't found one in Turkey. I am not new to C programming but I'm new to ARM architecture. I will be brief. I want...
Hi,
I wrote an application based on ATT_MTU Throughput Example. Now I'd like to add support for Thread protocol. Is there a possibility for adding OpenThread libraries to...
Hi to all, I have just bought NRF51 DK from arrow.com I couldn't found one in Turkey. I am not new to C programming but I'm new to ARM architecture. I will be brief. I want...
Hi,
I use sdk 12.2 for my production software with UART protocol, my product is distributed to customers since 6 months with many type of phone or tablets using it without...
I have inherited a project where the Makefile sets __HEAP_SIZE and __STACK_SIZE for both CFLAGS and ASMFLAGS:
CFLAGS += -D__STACK_SIZE=2048
CFLAGS += -D__HEAP_SIZE=0
...
First of all I want to say hello. I'm new in nRF52 devzone and I have problem with ble_app_uart and ble_app_hrs programs. I use pca10040 board and eclipse for flash and debug...
