Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi, I was wondering If I need to wait for a response from the server that a command was executed before executing another command or if the BLE stack takes care of this under...
Hello
i m searching for a method to send a big buffer with TWI to a slave. The Buffer is read from flash. because its a soundfile its needed to send the buffer without delay...
I am trying to set up a nrF52 -> Rpi v3 -> Exosite through CoAp as in the nrF5 iot sdk. The nrF52 to rpi works as I am able to ping the nrF52 through its global link address...
Hi,
I am writing a code base on the reference manual of nRF51422. In section 29, UART, I don't understand the differences between TASKS, EVENTS and REGISTERS. Aren't they...
Hello!
I'm trying to use the ram_retention in sdk 15 alpha to retain RAM in system off mode and do some power profiling.
The default code seems to retain 8 kB of RAM...
My project needs to use 2 different TWI instances and 1 SPI instance. I knew that it is not possible to use three instances at the same time in nRF52.
To implement 2 TWI...
Hi Nordic,
I am trying to enable the DC/DC converter on a PCA20006 rev 1.3.0.
I am using the softDevice S130.
1. Using the sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE...
Hi.
I am using saadc example code or SDK V13 with the following requirements:
Voltage input up to 70mV,
Resolution: 50uV
So I did some modification to support...
Hello,
yesterday I got a Thingy:52 device at an event held in Frankfurt/Germany. At home I've tested the DFU for the latest firmware and observed that the image was transfered...
Hi,
I’m having some troubles with example code : ble_app_uart_s132_pca10040. The code compile well in Keil and I can prog it in the nfr52 but it doesn’t run. When I check...
To enable comparability with an existing client, I'm attempting to configure the nRF51822 to provide a GAP service that includes user description descriptors (UUID 0x2901...
I'm trying to store some values with fstorage. The store operations seem to be queued successfully, but never executed. I currently have this to test the behavior:
FS_REGISTER_CFG...
Hallo everyone,
I am reciving a notification from my server, which lenght can be 8, 20, 30 bytes but when I want to display the info using NRF_LOG_INFO is not printing...
