Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I searched over the website, I couldn't find a good introductory documentation for programming the nrf51822, specifically the nrf51-dk. I have a transistor hooked to p0.01...
Hi Team,
Is it possible to have multiple profiles like serial, heart rate monitor, proximity etc. in single code?
What are the efficient ways to do it?
Regards,
M...
Hi,
I'v a query regarding the two development boards PCA10001 & PCA10028.
I have worked on a project with development kit PCA10001 and made the release to customer ...
I have followed the instructions and have tried with s110 6.0.0 and SDK 5.2. I can compile and download to the board but can never detect under discoverable device onn MCP...
I am running ble_app_uart in my pca10004 board. The crystal configuration is set to 32khz crystal.
But i want to use the 16mhz external crystal for my use ,because my application...
Hi!
(I moved this question to the "Questions" area from another area.)
I am using Eclipse to develop and debug on nRF51 DMs (PCA 10028). I have managed to run and debog...
Dears,
Just one question for RTC.
In SDK9.0, it's possible to control of time to use HW RTC block??
If possible, please let me know how to use it..
Thank you.
Lets say I have 200 bytes of data that I want to store in flash. So, I request a 200-byte block.
In order to store, the area has to be cleared first. As far as I understand...
Using the nRF51-multi-role-conn-observer-advertiser-master project to test timeslotting I have encountered two issues (Softdevice s110 7.1)
Issue #1: Repetition of advertisement...
Now, I need two function add my project (On BLE stack).
Distinguish long/short press at same button.
2.device and master synchronous time.
No.1 question is...
Hi
We have custom nrf51822 board.
in that we have nor flash which is spi compatible.
so in order to read device id i used spi_master sample source code.
i am able...
Hello,
I'll explain my code:
NRF51 takes samples of a sensor every 10 minutes. In addition, softdevice S110 is used... An user can connect at any time, so advertising...
I am trying to implement frequency counting on nRF51822 by counting number of pulses in a given period. I create a PPI channel with a GPIOTE event on rising edge linked to...
Hi,
is it possible to mount a nRF51822 in an aluminum enclosure and use ble?
I am looking for a range of up to ten meters in an open area.
Is that possible or will the...
