Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hello,
I recently updated the asset tracker on my thingy 91 with the lastet available pre build firmware (2019-11-29_d3130d77) using MCUBoot.
Since my Thingy91 is only...
I started with the mqtt_simple example.
I added:
#CONFIG_MQTT_PASSWORD="pass" #CONFIG_MQTT_USERNAME="David"
to the prj.conf file. Relaunched the project which rebuild...
As a matter of fact that there is no special EEPROM in nrf52832 , the user data which need to be stored in nrf52832 should be written into the flash of nrf52832 . The SDK...
When debuging nrf52832 , the code can be flashed into the flash through JTAG . However , I need to reprogramme the nrf52832 through UART interface . It seems that there is...
Hello.. I use RNF52840 Dongle. I compiled the blink example with VS code and I programmed with nRF Connect tool.
now I can't connect the USB device. I read that I had to...
Hello,
I am currently aiming to create an application for the nRF52-DK using the nRF5 SDK and Segger Embedded Studio as my IDE.
Due to the SDK itself being extremely extensive...
Hello ,
I have been trying the Zigbee CLI light example.
And I modifed the main.c file to have the network saved "ZB_FALSE" and then flashed the updated hex file to 52840...
Hi we are having issues with gpiote interrupt. We would like to do some spi read when drdy gpio becomes high to low. I have done above configuration for the same.
We are...
I have a problem collating model publish events arriving at two different nodes in my mesh.
My application is an array of sensors publishing through generic on off and generic...
Hi,
I have a custom board running NUS peripheral which uses the nRF52832 and a NUS central which is running on a nRF52 DK. I modified the ble_app_hrs_freertos example to...
Hi,
I found the communication range using FREERTOS is shorter than which are using non-RTOS.
I know the RADIO TX power and the PHY rate affect the communication range...
Hello,
I am using nrf52832 Dev Kit and am attempting to send information using the ble_app_uart example under SDK version 15 (I don't know the exact rev, but I downloaded...
Hi,
I am using nrf52832 in my custom board and I want to make secure connection between my two boards using stored keys.
Is there any example provide by nordic which I...
I am using the nrf51822 ble with s130_nrf51_2.0.0_softdevice and want to know if the broadcast can start at a given time, and if the adv_ interval can change everytime? (such...
