Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello I have what I hope is a simple question regarding the Internal DC/DC on the nRF52832 and thus nRF52810. I am assuming it is the same internal design, correct between...
We are just in the very beginning of developing a mesh network with 150 devices and a gateway (with a nRF52840 in it). We want to find the best strategy for provisioning....
Hi everyone,
thanks for this discussion - this question addresses almost exactly a potential use case I've been looking into.
I'd like to try and implement something this...
This is from the documentation:
[in,out]
p_length
Pointer Length of the string. Amount of sent bytes.
I'd translate it to a pointer to the requested length...
Hello all, I already did some research finding similar questions and answers in this board, unfortunately I still do not have answer, maybe some can can help pls?
I have...
Hi,
I'm trying to test the BLE Mesh example. I want to prove that whether the feature of Relay is able to work or not. So, I use the functionality of heartbeat publishing...
I am running SDK 14.2.0 and trying to update only the bootloader. Very minor changes were made, resulting in no size increase.
I ran nrfutil (V3.4.0) using the following...
Hi, Everyone
My development environment is PCA10028, SoftDevice 130, SDK12.3.0
I am testing the input and output of the uart using nRF5_SDK_12.3.0_d7731ad\examples\peripheral...
Hello!
I am using nrf52832 with SDK14.0 and SD 5.0.0
I have issue with Flash data storage. I am using code from example (fds_test from github)
Writting works good...
Hi,
nRF52832 uses which type of modulation technique?
Whether nRF52832 is Adatpive euipment or Non adaptive equipment . Please clarify?
Wireless module certified individually...
Hi all,
I am merging my code from Mesh 1.0 to 2.0.
I am trying to put both Provisioner and Simple On/Off Client into one board,
and then the other board is simple...
Hi,
May I ask what's the minimum reference circuitry for running nrf52810 without RF? Thanks.
Our need is as follows.
1) RF, eg, Antenna is not needed 2) GPIOTE 1 channel...
So I have my dongle sniffing for BLE packets and I can see all the advertising packets coming from the device, even the SCAN_REQ and SCAN_RSP.
But as soon as I paired the...
Hi Sir
The product is nrf52840 and SDK15, If I'd want to do following SPI operation ( CS to L ---> MOSI data {0x60, 0x00, 0x00, 0x11} ---> CS to H )
1. How to setup nrf_drv_spi_transfer...
