Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
hello! i have a problem ,when the Master send Slave SMP 37 Rcvd Pairing Request: Bonding, MITM, Initiator Key(s): LTK IRK CSRK , Responder Key(s): LTK IRK CSRK,but the slave...
Hello,
Thread Topology Monitor can associate an user name with a device. Where is it stored (in computer application or directly into the device) ? If it's in the device...
Hello All,
I am trying to interface an analog sensor with nrf52832, whose analog values have to be converted using SAADC and has to be sent over SPI to another chip. But...
I am testing the NR52832 using a BMD350 module on a custom made board.
Using the SPIM i faced the problem that i got an extra 500uA of current randomly. After trying to...
Dear Nordic,
We are using NRF52832 + RFX2411N for our product, and for lower the power consumption. we wonder if there has any way to know the CONNECT_REQ event.
In advertising...
After some time debugging an issue I had, I found out that my code was setting the I2C interrupt priority to 0, and at the same time that I'm running a Soft Device on my nrf52832...
Hi,
The Ch. 16 Power Supply Section of "nRF52840 Objective Product Specification v0.5" mentions the two power supply mode of nRF52840. This supply is available on the respective...
Hi.
I’m trying a multiperipheral function and have a problem.
The problem is I can not notify stable battery voltage with SAADC to the connected Central while advertising...
Hi, everyone,
We are developing BLE project on the nRF52832 chip (SDK 15.0) that must transmit to the big distances for about 20m. We set the transmission power to +4dBm...
Hi Dear nordic employee
I want to test the accuracy of my external LFCLK,
1、I enable the nordic RTC
2、set the prescaler 31(32768/32=1024),1/1024 second per step
...
The temp accuracy is stated at +/-5C. Does that include using piece-wise linear terms for accuracy? Is there any data on accuracy over a narrow temp range such as 0-40C? ...
Hei, I couldn't really find a question regarding this use-case.
I'm hoping to interface a USB (2.0) charging capability to my design and thus I need to have a communication...
Hi Nordic,
Does FDS affect PPI ADC acquisition when writing data? The test found that once the FDS is written to the data, the ADC data returned by the PPI ADC is fixed...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I would like to ask about WDT and softdevice (centre).
The WDT setting is 2s timeout and the WDT...
Platform: windows
hardware revisions: PCA10056
nrf5 SDK: 15.2.0
mesh SDK: V3.0.0
IDE: Keil MDK \ SEGGER embeded studio
I want to use keil to develop mesh projects...