I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
I used nRF52833 sdk17.1 to develop a device that is now going to use long distance. 17.1.0\examples\ble_peripheral\ble_app_uart\pca10100. Now what can I do to use his long...
Hi,
Using the Zephyr how can I set a TWI module clock frequency different from the standard speeds?
With nRF SDK I was able to do this by setting "frequency = 0x00290000UL...
Hello,
I am working in ncs1.5.0 on a nrf52840dk based custom board. I have found an issue where adding a certain number of characteristics in a single BLE service causing...
I have a general query regarding using ov7670 camera module with Zephyr SDK.
I have some of these camera modules available and I would like to try out how it works using...
This question is analog to but related to a Matter application. In this case, I'd like to separate the compilation of all Matter/CHIP related application parts from my own...
I am trying to use the ICM42688 sensor on I2C BUS with nrf5340 Application core. In the configuration, the HAS_I2C_RTIO config couldn't be enabled. Is this an MCU limitation...
I am trying to run the blinky Demo on the nRF52DK on VScode, the whole process is smoothly, but it can't work, the LED no any action. could you know anything I miss? many...
When I was making the upgrade package, I encountered a problem, and there was no problem in making only one upgrade package.
It is also possible to make protocol stacks...
Hi All,
Using VS code, nr52840dk,v2.6.0sdk，sid_end_device demo, No changes have been made
Firstly, add build config
Then click on Flash
Clicking VCOM0 has no logs...
Hello, I'm using the example "smp_client_ble," and I can't manage to remove the boot message.
Below is my .prj file:
My toolchain is: NRF Connect SDK V2.2.0
I am...
The chip I 'm using is the nRF52840, the sdk and toolchain versions are both 2.5.0, my code is here :
When I call spim3 peripheral with nrfx library, I add
CONFIG_NRFX_SPIM3...
Hello, hope to find you well. I'm a beginner involved in a project that's migrating from the old SDK to NRF Connect (VSCode). The project uses nrf_crypto.h and nrf_crypto_rng...
We recently purchased the module 453-00052R from Digi-Key and have successfully implemented it into our project. The design is complete, and we are now attempting to flash...
Hi,
I am trying Asset Tracker V2 application in my custom board and rechecking results with DK to ensure no hardware reasons are there. Using SIM supplied with DK and...
