I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hi,
I am trying learn about IO/ events that can wake-up nRF52833 from lowest power mode.
What qualifies as event that can serve as wake-up source?
Is it possible to...
Dear sir,
Got error while uploading .zip in DfuTarg as "SD version failure". I'm using nRF52840 DK board. I have tried to create .zip by --sd -req 0xB6/0XAE/0xA9. zip get...
I'm curious what the modem does if, upon waking up to service the PSM interval, it fails to connect? Does it go back to "idle" and try again on the next PSM interval or does...
Guys, In a Mesh project, when setting up flash manager:
How do you get the right value of flash_manager_config_t.p_area ?
And where and how is it configured?
Thanks...
Hi ,
I wirte a python script to download FW to nRF52832 custom board, the FW is the merged file with softdevice（s132_nrf52_7.0.1_softdevice.hex）, bootload, bootload settings...
The version used is nrf5_SDK_for_Mesh_v5.0.0_src.
nrf5_SDK_for_Mesh_v5.0.0_src\examples\light_switch\server.
Question 1: I want to turn off mesh broadcasting first,...
Hi
data sheet of the nRF52840 states that the QSPI port pins should be initialized to "high drive".
I've experimented a little bit because I have problems with a Macronix...
I have connected a BM680 sensor on a BL654 (NRF52840) via I2C. I have connected the power to the BME680 on a switchable power rail. I need to power this rail with a GPIO pin...
I am trying to create a test case for in house validation and would like to know how to do so.
Here is what I want to do:
I want to create a boot loader that checks...
Hello,
In nRF5_SDK_17/examples/dfu/secure_bootloader/main.c, the main program starts off with protecting a couple of flash areas:
But how can, after this, an OTA update...
I don’t know what all the XML syntax is, or what program processes the flash_placement.xml file, or what form the output is in, so I don’t know if I have to do exactly what...
Hello, nrf experts.
I have trouble with testing update over ble from main application. Using buttonless dfu example. But when I'm connecting to nrf dev kit, nrfConnect on...
Hello, I am trying to erase a page on the internal flash memory of the nRF52840. I am doing this as a BLE peripheral with 1 active connection. The problem I'm facing is that...
I am trying to determine the cause of iOS stopping to reconnect to my nRF peripheral in the background. I have seen posts from several years back that reconnecting too many...
Hi
I'm trying to add CMSIS DSP Software Library to my project.
After adding DSP function I'm getting linking error:
components/toolchain/cmsis/dsp/GCC/libarm_cortexM4lf_math...
