Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I'm working on an NRF52832 product that will be intermittently powered, and the supply rail may fluctuate slowly, drifting above and below 1.8V.
I saw this post:
https...
Hello everyone
I am using nRF52840+wifi module to communication with the server via MQTT+LTS, Now MQTT communication with server was successful, Considering the safety,...
Hi everybody!
We have a problem with our product. It is based on nrf52832.
We used heart rate example in the SDK. MCU sleeps after a while if it is not connected. We have...
I'm trying to combine conventional pairing with OOB NFC pairing, but I'm struggling to decide which libraries to use. I have been looking at the examples, and they all use...
how can we properly set the scan timeouts? Say if we need to scan for a device for 5 seconds and if it is not available we can stop the scan and search for a new device. i...
Hello I am getting fatal error and system reset after calling APP_UART_FIFO_INIT.
I want to receive some data over ble and send it to the uart. I connected physical UART...
Hello, in my application I have a problem with the app_timer module respectively with a timer I have created. I'm working on a nrf52832 ( Rev. 1 - build code QFAA-B00) and...
I need a solution for doing a DFU from an Android phone to a device with a nRF52832 chip in it
I currently have a working version in IOS Swift but cannot get the Android...
Hi everyone,
I'm using nrf52840 custom board (pca10056)
SDK version: 15.3
OS: Fedora
I work on a custom board and try to use WDT like so in the WTD project example...
Hi,
I implemented the rnd example under ../crypto/nrf_cc310/rnd with freeRTOS. While testing i observed strange behaviour.
While debugging i got
=================...
I have been using nRF9160: LTE Sensor Gateway to send data from nRF52832 and it all seems to work fine. However whenever i switch off the nRF52832 I receive an error as attached...
As stated on the product page and repeated in my title, the nRF24lu1 and the plus model aren't recommend for new desifde. Is there an nRF52 series replacement?
I'm working...
Hello,
I am developping an application using Softdevice which works (or worked).
Then, as I also need using UART, I built and flashed the example program nRF5_SDK_15.3...
My goal is to replace the legacy bootloader present in nRF52832 with a new bootloader with the DFU process.
I am using nRF5 SDK v15.3.0, GCC ARM and S132.
I have done...
