Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hi,
I'm having some difficulty debugging an issue with the mqtt library on the nrf9160dk.
I have written my own Cmqtt library class that wraps the Zephyr mqtt library...
Dear ,
On Windows 10 Bluetooth add a device,
Why SDK_17_0_2 Example does Bluetooth be disconnect immediately after pairing
(Use about \nRF5_SDK_17_0_2\examples\ble_peripheral...
When I open the Light Bulb project in Segger Embedded Studio I see a bewildering list of project items. I pick the first project, 'zephyr/merged.hex' and right click to set...
SDK: 4.1.0
CHIP: 52840
Hi, I have developed sleepy zed. It lost the connection with the network after joining in 1~3 days.
It assumes that the zed couldn't get the...
Hi, guys.
I'm using nRF52 DK (PCA10040). After I used Zadig (Driver setup for J-link), I cannot build and run my previous code to the nRF52 DK anymore (see the first 3 images...
Hi
I am using nrf52840 boards and by using the coexist program I am able to send and receive messages through mesh while using the ble services.
I followed the instruction...
I use NRF52DK as central device I also use a SDK that is ble_app_uart_c code for my project. and i would like to take my peripheral devices whice are phone or PC their RSSI...
Hello - we're using "nRF Connect" from the Apple App Store for the development of our project.
First, thank you for making this tool available and free for everyone to use...
I am using nrf52840 via NRF Connect and Zephyr configured to use the Nordic SoftDevice BLE controller.
My use case is for a central to sample a rapidly changing real-time...
As a beginner,I’m sorry for asking such a stupid question,but it has annoyed me for a long time.
I built and downloaded the program to my DK,and I used PuTTY to connect...
Hello,
I've designed a pcb using the 52840 chip which is essentially identical to the dongle design. My intent was to use the firmware that comes pre-installed with the...
Is there a set of prj.conf settings that I can use to redirect the AT command interface to the RTT debugger? Would be nice not to have to hook up a serial connection.
Hi All,
as the title say I'd like to know if is the Wake on GPIO available for nRF52840_dongle and what is the I OFF_RAMOFF_GPIO ?
My application should behave more or...
Hello. I'm developing a project using nRF52840. I've been working with the nRF52840Dev Board and I have a BLE project that runs there. I'm developing in Segger IDE and using...
When building a product which has multiple models but the firmware is essentially the same, perhaps with a few different parameters, I want to use the same code base and have...
