Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I hope someone is able to answer a few question.
I read quite a lot but still some things are still confusing.
If we use e.g. the AMB2621 Module of Würth, is skipping...
Hi,
I am trying learn about IO/ events that can wake-up nRF52833 from lowest power mode.
What qualifies as event that can serve as wake-up source?
Is it possible to...
Dear sir,
Got error while uploading .zip in DfuTarg as "SD version failure". I'm using nRF52840 DK board. I have tried to create .zip by --sd -req 0xB6/0XAE/0xA9. zip get...
I'm curious what the modem does if, upon waking up to service the PSM interval, it fails to connect? Does it go back to "idle" and try again on the next PSM interval or does...
Guys, In a Mesh project, when setting up flash manager:
How do you get the right value of flash_manager_config_t.p_area ?
And where and how is it configured?
Thanks...
Hi ,
I wirte a python script to download FW to nRF52832 custom board, the FW is the merged file with softdevice（s132_nrf52_7.0.1_softdevice.hex）, bootload, bootload settings...
The version used is nrf5_SDK_for_Mesh_v5.0.0_src.
nrf5_SDK_for_Mesh_v5.0.0_src\examples\light_switch\server.
Question 1: I want to turn off mesh broadcasting first,...
Hi
data sheet of the nRF52840 states that the QSPI port pins should be initialized to "high drive".
I've experimented a little bit because I have problems with a Macronix...
I have connected a BM680 sensor on a BL654 (NRF52840) via I2C. I have connected the power to the BME680 on a switchable power rail. I need to power this rail with a GPIO pin...
I am trying to create a test case for in house validation and would like to know how to do so.
Here is what I want to do:
I want to create a boot loader that checks...
Hello,
In nRF5_SDK_17/examples/dfu/secure_bootloader/main.c, the main program starts off with protecting a couple of flash areas:
But how can, after this, an OTA update...
I don’t know what all the XML syntax is, or what program processes the flash_placement.xml file, or what form the output is in, so I don’t know if I have to do exactly what...
Hello, nrf experts.
I have trouble with testing update over ble from main application. Using buttonless dfu example. But when I'm connecting to nrf dev kit, nrfConnect on...
Hello, I am trying to erase a page on the internal flash memory of the nRF52840. I am doing this as a BLE peripheral with 1 active connection. The problem I'm facing is that...
I am trying to determine the cause of iOS stopping to reconnect to my nRF peripheral in the background. I have seen posts from several years back that reconnecting too many...
