FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
Hi DevZone,
Does anyone have any experience with performing a SD-Card format with the nRF52840 . This is to avoid removing the SD-Card from the hardware when a format...
Hi,
I tried programming the nRF5340PDK using the nRF connect programmer, but when I select the board I get the following log:
2020-11-11T13:04:58.307Z INFO Application...
Hello,
in our project we have a nRF52840DK as central and a BMD-300 (contains nRF52832 chip) as peripheral. The software on the nRF52840DK is based on the ble_app_uart_c...
I have a project where I am distributing code images to a number of devices with DFU (this is a custom bootloader)
The peripherals use a mixture of 52840 and 52811 SoC...
Hi,
I am currently using the nRF logging module to log data from a nRF52832-DK to my laptop via a serial connection. However, I would like to move over to BLE logging for...
I doing some basic antenna tests via RSSI and the logger output is quite important to me. So far, I managed to log my RSSI values and timestamp, as well as the ID of my devices...
hello Nordic
i am using nrf52832, sdk 16.0, s132 v7.01
i am scanning for ble beacon but i want to be able to change the filtered mac address (i still want to filter...
MCU: nRF 52832 SDK VERSION: 17.0.0_9d13099 SOFTDEVICE: 7.0.1 (s132)
I have an application with some custom services (4) with different characteristics number and behavior...
I was able to change the MAC address in the ble_app_buttonless_dfu example with "sd_ble_gap_addr_set( )".
But, when I enter the DFU mode, the MAC address changes to the...
Hello,
i am using nRF52832 Development kit.
and segger embedded studio for debugging
i have just started with NFC module. i run the NFC example "record_url" and it is...
Hi,
In the process of testing DFU on the hardware, I am trying to send the DFU Packets through a TTL Cable to a different pins(P0.02, P0.03. No HWFC) instead of sending...
Hi Sir
As subject, I have a nRF52-DK on hand, I'd like to use the "Bluetooth Low Energy APP" of the desktop nRF connect software to scan BLE device and connect it,
Just...
Dear community, good afternoon
We have been working with a coordinator, a router device and an end device all based on nRF52840 (Fanstel BT840F module) with nRF5_SDK_for_Thread_and_Zigbee_v4...
Hello,
I am trying edit and compile mcuboot and ultimately upload to the nrf9160.
To do so I am loading the mcuboot project using CmakeLists.txt at v1.2.0\bootloader\mcuboot...
Because the nRF52840 consumes an additional 1mA when QSPI is activated, Nordic has previously recommended deactivating QSPI when not in use, which in practice means deactivating...
