I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
We have a working app for SDK 16 and freeRTOS. We wanted to update to SDK 17.0.2 but after upgrading the app hangs up at the first vTaskDelay(). We use configUSE_TICKLESS_IDLE...
Hello, I am a newbie in this forum and I'm not very familiar with app development in general, however I am in the situation in which I have to develop an app to acquire ANT...
Hello Nordic Team,
I am having issues with the HCI UART firmware for the nRF52840 on the Thingy91. I have been using the HCI UART firmware from nRF Connect SDK 1.0.0 for...
Hi, I am working on a project to send commands from mobile to device and vice versa. I am using nRF5_SDK_17.0.0_9d13099\examples\ble_peripheral\ble_app_template . I have made...
Hello,
I am using : SDK 17.0.2 and S132_7.2.0 with nrf52832 DK
in my BLE application, the FDS has 2 behaviors :
1) When the softdevice is enabled : fds_write returns...
Hello,
I´m searching some information about the NB-IoT protocol stack and the overhead which is send with every message.
I nearly searched the whole net but didn't find...
Hi,
It has been stated that nRF9160 doesn't support RLC UNACK, which we have also observed with nRF9160-DK in signalling mode against radio communication tester. Are there...
Hi,
I have a setup where mobile device(central) connect to nrf51dk (peripheral) and exchange data for a time. I want to detect unplanned disconnection of mobile device in...
Hi all, I try read DEVICEID in non-secure application but always return "BUS FAULT", I tried too enable NRF_FICR register in "spm.c" but the error persist!
I try
NRF_FICR_S...
Good morning Nordic,
I am trying to configure the I2C pins for our board (using nRF5340-QKAA SoC) but I cannot find the pin numbers for I2C_SDA and I2C_SCL.
All I could...
Hi all,
We are using the BMD-340 from uBlox, which runs the nRF52840 SoC.
On this BLE Peripheral, we are running the ble peripheral demo project ble_app_uart (pca10056...
Hi,
I am trying to disconnect an Android smartphone from the nRF52840. After trying for some time we found out that the BLE stack of Android does not reliably closes a Bluetooth...
hi..folks
wish you happiee new year
i am using nrf52832 whille i tried to pair my device with my android , i am getting an error message " pairing rejected by nordic_uart...
Hi,
According to below thread, the advertising interval has a random 0 - 10 msec delta, so if the adv interval is 20 mses, if run it for long enough, will the result be...
Hi,
I would like to use the PDM interface for my application in nrf52840.
I configured the driver, and started using the SDK's API successfully.
Question 1:
During...
