Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Dear nodic engineer:
i want test environment temperature with NRF51822 inner temperature module.
any information for reference?
any temp graph?
if need calibration?...
Hi,
I have an evaluation kit and I have custom boards that has nRF51822 chip on them.
I am trying to update the firmware(Application) of the custom boards from evaluation...
Hi,
I need to drive a piezo buzzer. Just need to make a simple beep function(s) that one call will start generating a specified frequency on specified pin and other call...
there is no sample code in nrf5188 sdk to use BLE_GAP_CONN_SEC_MODE_SET_SIGNED_NO_MITM,
what's the difference between the two settings?
for BLE_GAP_CONN_SEC_MODE_SET_SIGNED_NO_MITM...
Hi,
I am using IAR Workbench for ARM to develop my application and I'm experiencing a very frustrating issue with my debugger (J-Link that came with the development kit)...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hi,
it happened that we have some hardware boards populated with older chips rev. QFAACA and some with newer rev. QFAAG0 but we need to share same software. As I read newer...
by set a char with BLE_GAP_CONN_SEC_MODE_SET_NO_ACCESS, means it can't be read and write, if so, why not remove the char?
any reason behind BLE_GAP_CONN_SEC_MODE_SET_NO_ACCESS...
Is there anyway to limit the number of channels a device is advertising on?
I'm using an nrf51822 with the S110 stack and want to limit my device to a single advertising...
Hi,
We want a throughput between a BLE link 12KBytes/s.
In our application there is a peripheral (in Nordic starter kit), running S110 and we have configured connection...
I have two questions.
Is it possible to use the DAP[n]/DAB[n] registers without using Bluetooth 4.0?
If it is possible, then how? I searched all the sample...
