Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello
I am at the early stage of evaluation of a nRF52840 USB Dongle and I have installed all software on my Win 11 PC.
Just trying to check that everything is working...
We have made 2 partition of Internal flash. One is for running Application and Other for storing some configuration. I am trying to erase the page of 2nd partition, and it...
Hi,
I have been performing a fresh install of the toolchain following the nordic's "nRF Connect for VS Code" page, as well as the YouTube video "Introducing nRF Connect...
Hello,
Developing a custom board with nRF9160 as application CPU and nRF52810 as BLE Controller. Connected via SPI + reset + irq lines to the 52810. The design is a copy...
This might be a simple one to answer but I'm struggling to find documentation on what to do here since we're still using an ancient SDK on 9160.
I have a working board file...
Hello,
We have a BLE connection issue. We want to connect a Windows 11 laptop with a nrf5340 eval board.
The connection procedure can fail by a disconnection with reason...
I have a custom PCBA with which has the flow of:
- Boot
- Advertise some temperature data read from TWI with a 5 second timeout using `ble_adv_fast_timeout`.
- I then...
I want to implement secure connections for a device based on the nRF52832, protected by a PIN/pass key, which I need to be able to configure dynamically, not hardcoded in...
Hi there
I am struggeling to find a solution to automatically connect to the controller when found based on the advertised name. I do not want to click on the found device...
Hello,
I am developing project on ESP32, with nPM1300. I am interested in battery state/capacity measurement provided by the Fuel Gauge example. Some part of the algorithm...
Hello. I followed the steps in the video to develop a project on my custom board.
www.youtube.com/watch
I created a new board and new application (blinky sample). Then...
I encounter problems moving to VScode + nRF Connect extension. Even the simplest step creates countless problems. I followed the official NRF tutorial on youtube and nothing...
Hi, in the development kit of nRF52840, the oscillator for the micro is configured as follow
In the bom, it can be seen that the used oscillator is the MP06003 that correspond...
To advertise a *configurable* device name the previous guidance seemed to be:
prj.conf
Code Snippet
Please note I have intentionally removed all error handling...
Hello,
I have multiple UART devices connected to various pins on my nRF5340, but due to hardware limitations, I can only use two UARTs concurrently alongside interfaces...
