Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hi there,
I always have to start up nrfconnect-5.0.2-x86_64.appimage and then select the power profiler. How can I directly start up the power profiler?
I can see that...
Hi there
I wrote a program (include of advertising, pairing and connecting over service, characteristics) for nrf51822QFAA and work well for C0 build code (nrf51822QFAAC0...
I want to know the power saving mode of nRF5340. Dose this chip set have the following mode ? 1. each BT products connencts, however, the data were not send. above condition...
Today I tried to use the bt_conn_le_param_update() method to update the connection parameters, using the following values.
interval_min = 3000
interval_max = 3000
latency...
Hello,
We can successfully build and flash the ncs/application/asset_tracker_v2 example code in nrf9160. But when trying to boot up, it throws the following error:
**...
Hi there,
I'm using a nRF5340 to generate an 8MHz signal and would like to force the HFXO to always be used as the HFINT is not accurate enough. I have verified this with...
Im following Lesson 8 Exercise 2 – DFU over USB.
My project is in its late stage and now I tried to add DFU over USB but Im getting #error "Serial recovery selected without...
Hi there
My costumer was not able to update the cpunet on a nRF5340.
A lot of troubleshooting now led to the insight, that the costumer used only the app_update.bin...
I had a project that was successfully building in Visual Studio code months ago (June 2024) with Toolchain 2.6.1 for the nRF52832. I have just had time to pick it back up...
Hi Support
I am just checking if Nordic supports hosts other than NRF hosts for the nRF7002 WIFI chip.
I am looking for support for the STM32U5 / STM32H5 mcus - for...
We are develping the BT production by using the Nordic sample program (SampleSoft_NRF5340-AUDIO-DK). ( nRF Connect SDK version is SDK25.0. ) Does this software certify to...
I have a existing design using nrf52810 soc I want send and recieve data using uart --->nrf52810 to nrf52810-->to uart data is custom and have approx 120 bytes, should I send...
I know this exact symptoms has been described many other times, and I apologize. However, I carefully searched through all the previously asked questions in merit and could...
when I run this application, it display Error :
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/applications/asset_tracker_v2/README.html
*** Booting nRF Connect...
