Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Let say during the normal program flow I want to change often the edge direction which will trigger the event: rising edge, none, falling edge, none … Can I work direct with...
hi:
i want to know CKCON config is CKCON =0x01 or CKCON =0x02? because datasheet is CKCON =0x01
External data memory stretch control. 001: One stretch cycle (default)...
Hi All,
I'm working with Nordic BLE Mesh and trying DFU (OTA) provided in sdk for Mesh.
I used \doc\getting_started\dfu_quick_start.md as the guide to setup and test...
Hello,
I am using nRF52840. I am trying to get hands on DFU. Without any modifications, I am using examples as is.
1) I followed below steps to do DFU hrs_application_s140...
I am looking for some 'getting started' information on configuring the nrf52833 DK for direction finding.
I have read the thread: https://devzone.nordicsemi.com/f/nordic...
Hello,
I have made a custom board based on NRF52840 IC.
The board is using GPIOTE, SPI2 and TWI1, and when put to sleep, consume 665µA. When just initializing the SPI...
Hi,
I would like to read accelerometer value from orientation_detector_calibrate() (in asset_tracker/src/orientation_detector/orientation_detector. c).
But from main.c...
Hi,
I am learning nRF development with 52DK device and SDK v16.0. I noticed that by default the 52DK planned P0.5~8 for UART purpose.
I am wondering if I can disable UART...
Hello ,
I am trying to send 1,000 of MPU-9250 data from NRF5832 peripheral(ble_nus_uart) to NRF52832 central(ble_app_uart_c).
And i have been searched this site and set...
I would like to move existing nRF9160 solution created according to nrfConnect Getting Started Guide to another directory under Windows.
Simply moving the folder doesn't...
Hello
I'm trying to implement interfacing between BME280 and nrf52840 on a custom board using zephyr BME280 sample example. I'm using SPI for the interface but there no...
I am evaluating the nRF Connect SDK for nRF5340. Currently, nRF Connect SDK seems to use zephyr's open source stack as the BLE stack.
By the way, nrfxlib / ble_controller...
I am developing application for nRF5340. I have two questions.
1. What value VTOR when reset? ApplicationCore'VTOR==0x00000000/NetworkCore'VTOR==0x01000000 ?
2. How to...
Hi,
i'm a beginner. now only i start with Segger studio & ble concepts.
i need internal RTC with calendar formats? i have check with the example programs , avail only...
