Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Greetings, I got a nRF52832 DK and only just found out that Smart Remote 3 is probably more what I'm looking for. It should be no problem to set it up on the DK with an appropriate...
I am working on a custom board based on nrf52810 that my client provided. In this board the accelerometer (Bosch BMA250E) power has been controlled by the PIN 9. However when...
Hi, everyone
I have some problems to make the Image Transfer Demo APP work
I have read the content of the website( https://github.com/NordicPlayground/nrf52-ble-image...
Hi,
I have 2 devices: one nrf52832 and one nrf52840 dongle. After enabling PHY feature (see the following code) in nrf52832, I tried to connect it using the dongle in the...
Hi,
I got the following hardfault when running sdk 14.2, nrf52832. Since the address shows it locates in softdevice...I do not know why. May you please give me tip? Thanks...
Hello, we have a handheld device with Microchip (ex. Atmega) Microcontroller that essentially monitors and records different environmental conditions and stores them them...
I am making PUC for sending & receiving string through ble nrf51822 to phone(nordic app) with particular user define time interval like 1 min , 5 min etc. using ble_app_uart...
I'm running \nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs and following instructions from http://infocenter.nordicsemi.com/index...
Hello,
We are using in nrf51822 in a product.
I do not understand whether by definition and, thus, always, before connecting, whether a peripheral
goes to sleep between...
Hi,
our device has a hard current limit of 2mA. Normal BLE operation is actually no problem. Connection parameters and packets/event are negotiated accordingly between master...
Hello,
I am using nrf SDK 15.0.0. I am unable to build ble_app_uart example in SES. It shows this error in the screenshot:
But i can build the same example using Keil...
Hi everyone,
I want to set LF CLK source to XTAL without softdevice. But, LFCLKSTAT value is 0x00010000(CKL RUN, CLK SRC = RC) after clock start.
So, I checked same test...
When drawing lines of equal start and end x, y coordinates the GFX library shall draw a rectangle with thickness applied. If the value of the opposing axis has a start value...
Hi everyone,
This might seem like a silly post, but this happened.
I build and ran the example QSPI code given in the sdk.
But after that if i try to run my own code...
