GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello,
I am using NRF52832, SDK v15.1.0.
For entering into various power down modes, does calling corresponding functions is enough to make entry into these modes or...
Hello !
In my project I have 3 phones, witch connects to one nRF8001(not at the same time).
First, phone connected, bonded and bond of this phone saves in EEPROM of avr...
I am upgrading our Nordic / BTLE library to the new sdk, which gains us ble 5.
The previous library (based on sdk 11.?.?) made light use of pstorage which, as far as I can...
I want to set up nrf24le1 in register retention mode with analog comparator wake up. The moment it wakes up it should do few ADC conversions and then again go back to sleep...
I have built up most of the support structure using the existing ble_app_uart example from SDKv15.0.0 and am now ready to port the code to our existing devices.
I'm having...
My environment is:
Windows 7
JLink Plus v9.3
IAR EWARM 8.30.1
SDK 15.0.0
Softdevice S132 from SDK 15.0.0
My hardware is a custom board with a Rigaldo BMD300...
I am observing a surge startup current of 0.1 to 0.2 mA when I am powering the nRF24LE1 module. Is it possible that the device can startup in power saving mode? Is there a...
Hello,
I have developed my own iOS app which is capable of DFU update different devices with nRF51 and nRF52 chips.
Using only APP file (both .hex and .zip) works perfectly...
Hello,
I' trying to switch from keil uVision to Eclipse, but it doesn't work as intended. I can't debug them (hrs with and with out dfu), but the Blinky example works...
Hi,
I'm working on a custom application using two microcontrollers a pic32 and a nrf52832, I require the pic32 using an external flash memory to read the binary file stored...
I'm interesting in knowing a little more about the "address match" output of the nRF905 chip. What is the expected jitter related to the actual radio signal?
E.g. If I...
Using softdevice s132, nRF52832 on a custom board
I don't quite understand how does the SPI work exactly?
I am using it on a battery powered low power sensor application...
Hi,
We are unable to run testing with Nordic nRF52840 preview DK boaed as it is not able to be put into DTM for RF-PHY testing.
I need the hex file to flash and the...
In the nrf52 specification:
"The Phase A, Phase B, and LED signals are mapped to physical pins according to the configuration
specified in the PSEL.A, PSEL.B, and PSEL...
Hello Everyboby,
I want to know how to configure can use Public address for advertising when using nRF connect APP? Now, I just can use Random address for advertising...
