hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hello,
I purchased nrf51822 module and i want to use s130 sdk for my project.
But when i have look over using keil i found that it requires jlink debugger or jtag debugger...
I am studying about developing a simple BLE 6LoWPAN network. My proposed topology is mentioned below:
internet - - - - - - - - - BLE1 - - - - - - - - - BLE2
| \
...
Hello,
As we can see, the mesh stack is a totally new stack which is independent of traditional BLE stack. Could you please explain why to design like this?
I found there...
Hi, I'm deeply interested about the Nordic's PCA20014; a.k.a solar beacon .
This HW uses
Amorton AM-1417CA solar cell, 1.5V, 12.5uA at FL-200lux
2 channel...
Hi,
I have run into a problem with the nRF sniffer. I used it in late May and early June to debug a BLE connection between a nRF-DK and a HTC Desire 610 and it worked fine...
Hello,
I am trying to communicate urart with nrf52840 and other devices.
But there was a problem.
You can transfer data from the nrf52840 to another device, but if...
Hello,
I need to connect an event handler (i.e. a function) to two NRF_RADIO events:
-NRF_RADIO->EVENTS_ADDRESS
-NRF_RADIO->EVENTS_READY
I know I should use the NRF_RADIO...
Hello ,
I can read the rssi value after the connection is established.
case BLE_GAP_EVT_CONNECTED:
APPL_LOG("Connected to target\r\n");
err_code = bsp_indication_set...
On this question it is said:
"Error code 0x3201 means BLE_ERROR_GAP_DISCOVERABLE_WITH_WHITELIST: Use of Whitelist not permitted with discoverable advertising ."
Why does...
It is not available in Digikey, Mouser distribution restricted to Sweden, not in Farnell???
Where one can order one or there is some problem or new version coming???
Hello,
i am working with SDK 14 type 4 tag library on NRF52832 hardware. I've based my code on the example "writable ndef msg".
When receiving a record, the NFC handler...
Hi All,
We are working with one of project where we are interfacing our nRF51822 with GPS module via UART . now the query is our GPS module works on 3.3V rx/tx logic but...
I'm building an android application using BleProfile classes in the nrftoolbox.
I want to request characteristic write to a peer(nRF51) in MyApplicationActivity inheriting...
Dear all,
I'm using 52810 and have some problem with the S112 softdevice.
My ble app problem is based on SDK 14.0.0.
I download my app hex and the S112 softdevice...
