pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Hey,
I am working on the nRF51 DK and nRF51822 with SDK12,S130, trying to pass a SIG PTS test for required IOPT, however always getting the same "INCONC" verdict, the PTS...
Hi,
I am trying to interface IS25LP064A External Flash with nRF52832 using SPI. I want to get the device ID/ Manufacturer ID of the flash. I am able to get the same in Arduino...
Hi everyone,
I'm using the nRF5SDK160098a08e2 and i tried to compile the ble_app_eddystone exampe but i'm getting this compilation error!
cannot find ../../../../.....
I am unable to read any uart input when I configure UART1 with nRF9160DK.
Please let me know if anything is wrong in my code/config
main.c
nrf9160dk_nrf9160ns.overlay...
In the Sleep mode and nrf52810 was Broadcasting with space 125ms once.
The normal temperature was good,that only 0.08mA. but why not 85℃，The current was up to 0.21 mA ,it...
Hello
I would like to detect timeout when I send a confirmable coap message not received.
My problem is that the response I receive in my response_handler is always...
Hello.
I'm going to make a prototype board and use it soon. I will make a prototype board with nrf52840 and use it soon.
It's my first time developing a prototype board...
nRF sniffer: v3.0.0
Wireshark: v3.2.6
Hardware: nRF52840 ( PCS10056 )
wireshark did not show packets with MTU greater than 20 bytes, is it still not supported?
Hello ,
We are using the following.
Module: Bm833 (nRF52833) from Fanstel
Softdevice: S140 7.0.0
SDK: nRF5SDK17009d13099
Sample code: ble_app_uart
We have added...
Hi, We are developing a BLE app on nRF52840. For the next step, we want to try reading/writing to other devices through connector interface on nrf9160 dk. Is it possible to...
I followed the steps below: flash softdevice flash bootloader
generate package
flash package
But after that I can't connect to this board by using usb and need again...
Dear Team,
I am totally new to NRF24LE1. I have bought 6 pieces it through online. Iwant to program it using HAL libraries. I've searched it everywhere I ca do. But I...
Hello, everyone.
I use the ble_app_uart on the nrf52DK board and SDK V17.
I would like to send data from the app using RX characteristics of UART service. The function...
Hi all.
I have written an application using a softdevice and I want to analyse an interesing behavior I don't understand at the moment. So I want to record a trace/log of...
hi!
Can anyone help me with code merging of saadc and ble uart.
Basically i have done analog to digital conversion of my sensor value and monitoring it on serial monitor...
