Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hi,
I working on a project that need to communicate with other mcu by SPI, the communication is work, but I have question about the start and stop of communication.
...
Hi,
I just met some difficulties to implant more then one service into my project. The project was developed based on hid_keyboard.
The project can work normally when...
I am using 2 nrf52832 boards to talk to each other through UART. One is programmed to the central SDK example and other other is peripheral. In the code, i incorporated 2...
Hi, I got the issuse about the connection with nRF52810. I used nRF connect to connect the nRF52810 device via Android,but it isn't easy to connect successfully.The nRF log...
Hello,
I have a question about the nRF52840 device and the supporting documentation. I am trying to figure out the current ratings for the GPIO. On page 198 it states that...
Hello,
I have an issue with the function sd_flash_write which ends up in a hardfault when returning to the function calling it. I know there are many Q/A on hardfaults...
Hi,
I have some questions about UART:
Currently I am developing software on our PCB with nRF51822 chip. When I was implementing and testing software on the Development...
Hi,
I am a beginner to BLE. I am using the nRF52 DK and i want to try out the advertisement and connection features.
I basically want to know how to send out an advertisement...
HI
when I use nrfutil.exe to generate .zip file on win10 64bit, I got the UnicodeDecodeError.
And :
Python version 2.7.9 (default, Dec 10 2014, 12:28:03) [MSC v.1500...
In my current project, I am receiving multiple indications from peripheral device. After 25 indications, I need to pause the indications or disable the indications. I am using...
I have a question about "LE Secure Connections (LE Security Mode 1: Level 4)".
I recognize that it is impossible to realize "LE Security Mode 1: Level 4" when adopting ...
I want to realize "LE Security Mode 1: Level 4". However, there is no IO capability in both devices.
I tried the following. 1) Set the IO capability of both devices to ...
I have a question about "LE Secure Connections".
I recognize that "LE Secure Connections" includes the following security modes and levels:
・ LE Security Mode 1 Level...
I run eraseall but the following error shows up. how can I fix it?
nrfjprog -f nrf52 --eraseall --log ERROR: JLinkARM DLL reported an error. Try again. If error condition...
Hi,
We have a requirement of reading the BLE Advertising name from flash instead of predefining it in as a MACRO. I saw in the notes it says to use ble_gap_cfg_device_name_t...
