Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hello,
In our application we don't allow bonding. Therefore I'm not allowing the application to send peer data to the bootloader using dfu_app_peer_data_set()...Therefore...
In NRF52-DK, I am currently working on NRF5 SDK 11.0.
In examples/peripheral/spi/pca10040/,
The master spi device is continuously sending "Nordic" string every 200msec...
I've submitted my product using nRF51822 chipset for Bluetooth certification. The BQE asks for QDID of proximity profile. Anyone knows about the QDID #?
Thanks,
Hello,
Is there a way to test packet corruption? My setup would be that I have my FW in nRF52-DK. Then I would test communication using nRF51-Dongle. I would like to force...
I want to connect two nRF51822-BKs and find their proximity. If one of the beacons go >5m away from the other beacon then one should beep/LED ON.
What is the best way to...
I have some troubles to understand the system clock functionality.
I am using a Module from Rigado which uses the nRF52 and has an external 32Mhz osc. on board.
In the...
Hi, I use the following.
Raspberry Pi 3 (RPi3 with Raspbian Jessie 4.4) as a router,
RPi3 is connected to a Wi-Fi router to access the Internet by using the built...
hi
i didn't manage to find detailed requirements on the voltage from the chip.
in the spec i see voltage range of :1.7-3.6v
but its not enough data for designing converter...
hi everyone, I am new to developing apps for nrf51822, and currently I want to learn first, I tried to google a lot around and could not look for the right resources, it would...
hi,
I would like to connect hid keypad with ipad,phone5s and android phone(all these have Bluetooth version 4 )but i couldn't connect this.ie, The nrf51822 module advertising...
I attempted to capture a waveform when running the SPI master example on nFR52 SDK/PCA10040. The source code I have as default and showing as follows
#define SPI0_ENABLED...
Hello,
We are working on a project that includes a countdown but we could not able to do it. Simply we want to do this:
Nrf51822 receives a signal-->run our funcion...
Recently, I've built up the latest OpenMesh v.0.85 example among 3 pieces of nRF51DK successfully. For my application, I would like to increase the data payload, is it possible...
Hi,
I am using Gazell for communication between two nodes. The first node is sending a sensor reading to the second node (which will be called henceforth the sink node...
Hello everybody
I have a nRF905 circuit sealed in a different medium than air and I am facing an 8 dBm power loss after sealing. I would like to know the following: Is...
