Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hello
Just few quick questions. What happens to the S110 Softdevice after the APP_ADV_TIMEOUT_IN_SECONDS period?
I'm using the nRF51 DK and the ble UART example and I...
As I am using nRF51422 EK (Evaluation kit), would like to know how to test with BT2.5 or lower version. Is this has backward compatibility. As when I give option of FLAG other...
Hello
I'm having difficulty in executing an GPIOTE interrupt during a BLE connection event with the nRF51 DK. The interrupt I have works fine when the softdevice is advertising...
If I set the centrals connection intervals values higher as a specific value it won't any longer find/connect/enable notifications on my peripheral.
0x00A0/0x0050/ 400...
After running the advertising_start () function in the sample software.
I set the breakpoint by Keil MDK-ARM v5 and stopped executing.
Afterwards, reset is generated!!
...
Hi,
I am using a gpiote interrupte handle function to send a notification to the master,but I find when the sd_ble_gatts_hvx() function is used,the interrupte handle function...
I have successfully completed dfu using android app, but if anyone can help me with example program so that i can perform dfu using program instead of using toolbox app, please...
On the XLR2 chipset I am seeing that if the RTS output follows the state of the CTS input.
When I load the same firmware in a XLR then RTS does not follow CTS
Hi, I am evaluating the use of ESB(without Ack) and BLE as a possible solution for my project since i have no use of Ack and in Gazell it is mandatory to use Ack. I had heard...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hello,
I'm drawing schematic with nRF51822 internal LDO. I'm wondering what is the regulated LDO output from nRF51822. I need to connect that with peripherals in stable...
We are using ANT with the nRFgo motherboard as base station and want to broadcast a signal over the largest range possible (> 100 m) to several mobile devices using the Dynastream...
I am designing a ECG monitor device. The data rate is less than 50kbps. I was planning to use BLE for the device design. But I read some documents that say BT classic is a...
Hello,
My 10031 dongle worked perfectly up to the point where I flashed it using MCP. I was able to run simple programs such as blinky, but now I cannot revert to the previous...
