Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hey all
I've some basic question about the Call-Stack.
In my application I have a series of functions which call other functions and so on until an depht of about 20 calls...
Hello. How i can do a simple read an 0 -> 3 Volt (vdd) signal on Analog 0 P0.03?
I try it with saadc without sucess
int result = 0;
NRF_SAADC->CH[0].CONFIG = (
...
Hi everyone, I know that this topic has been mentioned before, but there are a lot of doubts and the situation about measuring a battery is still not clear.
1) First of...
Hi,
Here i are using nRF52832 ,softdevice S132 and mesh sdk v3.0.0
I am facing an issue in UART configuration in mesh (LIGHT SWITCH EXAMPLE) server code . When using my...
Hi all,
I am building Border Rounter and Thread Network. I using SDK 3.1 and image newest for border rounter
I follow this link https://infocenter.nordicsemi.com/topic...
Hello. I am working on a application in a NRF5238 with s132, where I send 20 byte packets using notifications from a peripheral to a central board. The central is a modified...
I updated to SDK v1.0.0 today and have not been able to build sample or application solutions since. I updated the SDK, modem FW, and SES.
For example, when I open and try...
Hi,
I'm sorry to borther you in your holiday.I got a issuse about 52810 (s112) with PA.I found my device would reset when I call ble_advertising_start() after calling pa_lna_init...
I'm trying to implement Serial Wire Debug to read some Data from Nordic from other Controller. Initially Need to read some registers in DP & AP Nordic. For that I need to...
Hi guys, i was using nrf51822 s130 sdk, and now i am using nrf52dk s132 sdk. When i am using nrf_adc.h, all bitfields macro's get errors. It's bitfield macros doesn't match...
I am trying to connect BLE app to BLE Device ( NRF 52840 ) and for security purpose, I adding passcode (password) / key in the device, once I am going for connecting it will...
I used serial program to talk between nrf52 and arduino where the rx tx pins were default 8 and 6.When i changed the pins to 25 and 26 it is not working i am not able to communicate...
Hello
I'm looking for someone to help write a custom bootloader which performs FOTA update by using an HTTP connection to collect firmware. NRF52 is connected to GSM module...
Hello, Dear Support!
I explore examples in SDK 15.3.0 : ble_app_hrs and ble_app_rscs. The peripheral device in ble_app_rscs is configured to wait active request from central...
