In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Hi,
PTX:
based on the SDK11 "\examples\proprietary_rf\esb_ptx\pca10040\blank\arm4\esb_ptx_blank_pca10040.uvproj",
what I changed is delete the "nrf_delay_us(50000)" in...
I am simply trying to add a custom service to the HRS example. When I build in regular s132 armgcc it works no problem shows my blank service with nothing special. however...
Hi,
How can i disable peer manager from the buttonless DFU example. if just disable the peermanager by removing the code and editing sdk file, its not working.
i am using...
Hi All,
I am working on BLE+SD card.I am getting following error:-
*** Using Compiler 'V5.06 update 4 (build 422)', folder: 'C:\Keil_v5\ARM\ARMCC\Bin'
Build target...
I have a app that stores some calibration information in flash (1 page at 0x7F000)
When I booted now I noticed it has replaced it with "DEADCODE" following some hex number...
SDK version 12.2 and SoftDevice 132 and Dev. Board 10040
I am trying to run the ble_app_beacon example with NRF52832 DK. I have imported the IAR project into Segger Studio...
Hi,
I bought the nRF52840 in april. The problem is that my iPad doesn't detect the nRF52840. Also, when Itry to upload a .hex file on it, the board tells me that the upload...
Engineerings, We are looking around to find a way to prove that the hex file burned into the device is really the result of the original source code. Is there any idea/way...
Hi Guys, I try to implements the ctrl-C/V for bluetooth HID keyboard. But from SDK, I can't figure out how to send two keys. Even I do not use buffer_enqueue/dequeue in order...
Hello,
I try to build mesh sdk for nrf52840 it gives me error on RTT
0> <t: 0>, main.c, 318, ----- BLE Mesh Light Control Client Demo -----
0> <t: 0>, main.c, 108, Initializing...
hi, In my setup, I have a 3.7 V battery divided down to the bandgap range using a 100k and 100k resistors, so the voltage at the ADC input is 3.7 * (100/200) = 1.85 V. I am...
Hi
I used "nRF5_SDK_for_Thread_v0.10.0 - cli sample code and try to test Thread command "diag"
when I type "diag" then it will show "diagnostics mode is disable".
...
I am working on a project which involves sending data from many beacons to many other beacons. To be more specific, I have two groups of beacons:
The first group consists...
I'm planning to use one of those beacon platforms:
www.ebay.com/.../352167746226
www.ebay.com/.../112493464451
for a close proximity positioning system now I'd like...
