Hello,
I recently bought a Thingy91x; before that, I was using a Thingy91. I activated it and successfully programmed the Hello nRF Cloud firmware via the Quick Start in...
Hi All,
Previous last two times I opened my project in VS Code it displayed a deprecation notice complaining about SDK and toolchain versions. My plan was to address it...
Hey,
I’m currently evaluating DECT NR+ using two nRF9151 DKs with the nRF Connect SDK v2.9.0.
According to the ETSI specification (ETSI TS 103 636-4 V2.1.1), the Physical...
We urgently need to add support for Band 40 (B40) to our product. Our use case is very specific, and as far as we understand, the NRF91 currently does not support B40. We...
i just rebuilt the code in the beacon_advertiser.zip file attach to this issue for the NRF52232....
the code runs as expected, though consumes about 200uA when sleeping...
We are currently working on a project based on Enhanced ShockBurst (ESB) and would like to use Front-End Module (FEM) support with the nRF21540.
In your Enhanced ShockBurst...
Hi,
In my project I am developing a system to monitor the consumption of electricity taken from the grid. The nRF9160 SiP module is responsible for acquiring analogue signals...
Hi,
I found the TRACE connector on nRF52833 and 52840 DK has its pin 9 connected to ground.
But in the datasheet of JLink/JTRACE, the TRACE connector has following pinout...
Hi,
Could you tell me where can I find some guide how to add DFU into NRF BLE examples, e.g. ble_app_proximity ? I would like to add DFU like a service into the app, not...
We are having a very difficult time soldering the nRF52840 to the PCB. Our Operations Department is asking what the lead finish of the BGA balls is. Would be great to get...
Hi,
I compiled and downloaded GPS sample, I got the following messages:
Tracking: 0 Using : 0 Unhealthy : 0
Seconds since last fix: 600
Scanning [ _ ]
Over 10 minutes...
Dear All,
I have noticed the following behaviour:
When the modem goes to PSM, it is not possible to retrieve the RSRP, using the CESQ or the XMONITOR AT commands. This...
Hi,
I am using NRF52840 DK in our project . I am using 15.3.0 SDK and soft device s140 in our project .Here the nrf52840 dk board is client and other controller bluetooth...
Hello,
SDK: 15.3.0
Hardware: nRF52840-DK
I am attempting to make a simple dimmer with 2 pins/LEDs. I have used the following post.
https://devzone.nordicsemi.com/f...
After following all the steps on the nRF Connect v3.2.0 Getting Started Assistant.
I get the following error after pressing OK.
Any idea what is wrong?
Am I missing...
Hello,
I am trying to integrate the calendar example (using RTC 2), with a current time service(CTS) client and and custom service server on a nRF52940 DK.
I want to use...
Hi,
Firstly, I am able to read a 16-bit service with a 16-bit characteristic and able to use that to get a handle for reading and writing to the peripheral.
But i am unable...
Hello,
after the nRF9160 RRC connection the base stations inactivity timer determinates when the connection switches to RRC idle. Is there a AT command to read to the networks...
I am testing a BLE connection between a nRF52840 and a Thingy:52 using the nRF connect for Desktops.
It asks "Device must be programmed, do you want to proceed?" every time...
Trying to get started with the Thingy:91
- It's connecting to NRF Cloud and reporting data.
Problems:
1. Keeps blinking blue and does not get a GPS lock. I did leave...
