Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi nordic moderator team,
I'd like for you to reopen this thread https://devzone.nordicsemi.com/f/nordic-q-a/51673/nrf52832-sd_ble_gatts_value_get-or-catching-ble_gatts_evt_rw_authorize_request...
Hi,
I am using APP UART for Communication with slave device, the data transmission between two devices like send a command and get the response,
while getting the response...
Hi,
I faced a problem while building my project. Please see screenshot below
I think I have already include all the files and everything compiled. But this error shows...
I am trying to run smart remote 3 on PCA10040/nRF52832.
I use gcc makefile to generate PCA63519-SR3_nRF52832_Shield firmware. SD firmware is downloaded by jflash and I use...
Hi,
I want to update firmware on nrf52832, but I have an error: DFU insufficient resources
I found this and this , so I try to program my softdevice with this file: /nRF5_SDK_15...
Hi，
there is a issue very strange, on a nrf52832 project, it use two gpio set to sense low level, one is p18, one is p29, I found there is no response for low level of p29...
We are using nRF52832 with SDK_15.3.0 running the Nordic UART service (NUS) example.
Out of the box we find that the uart event handler is continually being called with...
Hi,
I have an SPI peripheral on pins 26, 27, 28, 29 which I'm able to override the default system's UART0 pin assignments in nrf9160_pca10090ns.overlay. However when I enable...
Dear sir,
We have interfaced a charger ic with NRF52832. It is having a charging status pin to show completion of charge. It is having 3 states
1. High impedance (Battery...
Hello guys,
Something strange is happening here and I need your opinion about that... I have a custom board with nRF52840-based BL654 module on it. I am using SDK15.3.0...
Hello
I am using nrf52840 chip. I am having trouble configuring SAADC to read analogue input on two channels (one signal is VDD of the chip). I have already searched the...
I am trying to get connected with my Android App and I have noticed that sometimes when the user turns off Bluetooth and tries to enable it again after 20 minutes my Android...
I am working from the ble_app_hids_keyboard example. To support multiple centrals, I imagine the first step is changing NRF_SDH_BLE_PERIPHERAL_LINK_COUNT and NRF_SDH_BLE_TOTAL_LINK_COUNT...
Hi,
I am trying to set up eclipse + gdb + openOCD for debugging zephyr 2.0.0. applications on nRF52832. Following the official Zephyr documentation build-and-run-an-application...
