Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Is there a way to change the scan interval while scanning is on?
I can stop scanning, set a different interval value and start again but that is not my intention, it wastes...
We have some nRF51 beacons kits and we want to connect some external peripherals using the available GPIO pins.
Does any one have an idea on how to solder some pin headers...
I'm trying to implement the ability to change the beacon properties (UUID, Major, Minor) using NRF Beacon Android app. My project is based on s110_nrf51822_7.0.0 (ble_app_beacon...
I'm working with the nRF51822, using the S110 soft device.
My application includes some measurement functions that are timing critical. Ideally, the code would be atomic...
Hi,
Can I use the J-Link Edu programmer to flash the nrf51822? Right now I'm using the J-Link LITE CortexM that I get from the development kit to flash the firmware into...
Hi folks,
I am struggling a little bit with Eclipse.
I just followed this tutorial ( embeddedsoftdev.blogspot.ca/.../eclipse.html) , the project compiles fine, but sometimes...
Hi everyone !!
I used to work with a RedBearLab module to prototype my bluetooth application, but since I have to plan the final version, I don't know which chip to choose...
I am using Eclipse Kepler, gcc and the nrf51 plugin ( sourceforge.net/.../) on OS X. I had an application that worked fine with SDK 5.2 and S110 Softdevice 6.0. I had been...
For my project，my ble device need to report firmware information to app， since the newer softdevices（like s130 0.5alpha） don't have FWID in UICR，where can I get it？
（Nrfgo...
Where can I find theta JC (junction to case) and theta CA (case to ambient) or equivalent thermal characteristics for the nRF51422 in WLCSP package? I've looked in the data...
Hi
in my project i need to interface SimpleLink Wi-Fi CC3100/cc3000 booster board with nrf51822
anyone care to share how to do that.
iam planning to interface via uart...
Hello,
I know there are already some post in that case but I have no idea what's wrong with my code. I've just downloaded code from: github.com/.../ unpacked to "\Nordic...
I have some code that works great on the Eval Kit. I would like to move it to the smaller form factor Beacon kit. I currently use the S120 SD. Is there an easy way to install...
Hi
The BLE module operates in 2.4 GHz spectrum with 3 advertising channels & 37 data channels . Why advertising require 3 channels ? is it possible to make it to one channel...
